Sorry guys. I am desperate to help but I just cannot give away a professional advantage that took both time and investment to gain.Well I have tried this and whatever way I use pin 6 on the outer wether it’s supply to the inner or joined it still gets out of sync over time when running. Where exactly did you connect pin 6? I don’t suppose @DJAlix is feeling generous today?
Sorry guys. I am desperate to help but I just cannot give away a professional advantage that took both time and investment to gain.
Danny do you have a sportback or a limo? Did you try the buck converter?
Its not voltage the problemDanny do you have a sportback or a limo? Did you try the buck converter?
Online coding is up and running, I need to test a solution that allows me to help you without giving away my professional advantage. Time is hard to find as I am almost fully booked. If you would like to investigate other solutions then let me know so I can cross this off my list.Update... still struggling with this Alex seems too busy and his online coding isn’t up and running yet. I have tried everything to do with wiring that I can find. Is there anyone with suggestions regarding the out of sync problem going from halogen to dynamic? Does anyone have a map of the 09 module from led car they could send me?
Online coding is up and running, I need to test a solution that allows me to help you without giving away my professional advantage. Time is hard to find as I am almost fully booked. If you would like to investigate other solutions then let me know so I can cross this off my list.
Happy to help, sorry it took longer to arrange than hoped. Am off to finish breaking this thing before bed@DJAlix has sorted it. Just another thankyou and as we all know here he’s the master of these things! Chuffed to bits!
Its my turn for tail lights conversion
I have collected all connectors nedded and waiting the dynamic lights from DPD....
I have some that will work, I assume you are converting the sedan not sportback?
I have a harness I made up for the sedan. If the connectors are the same I can send you some. You can see if they will work for you.
https://ibb.co/QCqRVkj
So I tried to code with obd11 as it was not supported last time I tried....then again I needed to have the engine off and i did this this and it was supported but still I get 3rd lower brake light on with signals. And both signals dont light up(outers). But they only come on when brakes applied...... plz helpHey, recently had euro taillights installed on my s3. Getting vith brake and turn signal lit up together. Apparently I need it coded... does anyone know the values? Somewhere in module 9 I'm guessing?
Sent from my SM-N950U1 using Tapatalk
are these instructions for the pre fl led tailights to facelift led tailights?
that's what I'm trying to do at the moment
can someone let me know what the wires in the pre fl plugs (outer and inner) are I'm having trouble following those diagrams...
like for example if I can get
outer own plug
pin 1 = ground
pin 2 = break light
would help alot
Hi, I'm doing the facelift rear dynamic light conversion as I type this message
I don't understand how to read wiring diagrams, but I have the facelift plugs and some wiring where the breaker that I bought the lights from chopped some wiring off the car for me to make it easier
I'm doing the outer lights at the moment, it's a Sedan 2016 model and I'm facelifting the lights to 2017+ model.
The PFL have 5 wires going into each
Nearside left outer
1-blue/white
2-yellow/blue
3-blue
4-red/brown
5-brown
Offside right outer
1-red/green
2-purple/brown
3-green/brown
4-brown/red
5-brown
FL have 6 wires
Nearside left outer-
1-brown
2-blue/white
3-blue
4-yellow/blue
5-white/blue
6-red/brown
Offside right outer-
1-brown
2-green/red
3-green/brown
4-purple/brown
5-grey/blue
6-red/brown
What do I do with these wires? Could I just keep the original plugs on the FL lights as the breaker left a fair amount of wiring on for me, and chop the original ones and exchange the wires over. It would be good to know which wire to change to which then it's a simple job of just cut, join and tape instead of repinning?
Hi, I'm doing the facelift rear dynamic light conversion as I type this message
I don't understand how to read wiring diagrams, but I have the facelift plugs and some wiring where the breaker that I bought the lights from chopped some wiring off the car for me to make it easier
I'm doing the outer lights at the moment, it's a Sedan 2016 model and I'm facelifting the lights to 2017+ model.
The PFL have 5 wires going into each
Nearside left outer
1-blue/white
2-yellow/blue
3-blue
4-red/brown
5-brown
Offside right outer
1-red/green
2-purple/brown
3-green/brown
4-brown/red
5-brown
FL have 6 wires
Nearside left outer-
1-brown
2-blue/white
3-blue
4-yellow/blue
5-white/blue
6-red/brown
Offside right outer-
1-brown
2-green/red
3-green/brown
4-purple/brown
5-grey/blue
6-red/brown
What do I do with these wires? Could I just keep the original plugs on the FL lights as the breaker left a fair amount of wiring on for me, and chop the original ones and exchange the wires over. It would be good to know which wire to change to which then it's a simple job of just cut, join and tape instead of repinning?
can someone let me know what the wires in the pre fl plugs (outer and inner) are I'm having trouble following those diagrams...
like for example if I can get
outer own plug
pin 1 = ground
pin 2 = break light
would help alot
also did you guys remove the bumper to run the wires?
also did you guys remove the bumper to run the wires?
i get the re-pining and all that but just curious to know how people ran the 12v from tailight inside the trunk and then the outer tailight wire to the inner