Yes, I'm sure.You sure it’s a S3? As far as I know, it would only work on FL A3 1.4 and RS3 since the ABS and might be other module is different on the other variations including S3..
This is apparently coding only. That's all i know.Would you need to install sensors for them readings?
This is apparently coding only. That's all i know.
It's a US 2017Might be working on wltp cars but definitely doesn’t work on my pre wltp facelift.
It's a US 2017
They're keeping quiet trying to figure out how to monetize it.Think we need to find out more from whoever that did this.
They're keeping quiet trying to figure out how to monetize it.
You need to purchase better quality LED's as poor quality ones always do this.Hey guys.
Can you help me with my interior lights?
They we're dump dome light, halogen and I bought 2 pairs of led to replace it with. So far so good but after 2 months they started flickering a little bit. Is there a channel in 09 where I can change them from halogen to led? Like you do for turn signal or reverse light?
Thank you
I could sell you some LED's for £200 does not mean they are good quality lolI did, I payed 25€ for a pair, I tought they we're good quality
But no coding for this?
Thank you!
I could sell you some LED's for £200 does not mean they are good quality lol
Contact @t8ups via the forum. He will supply ones that work with no issues.
Cannot adjust the physical ride hight through coding on our cars. What can be done via coding is a re-calibration to tell the vehicles what it’s true hight is so that the magride system (if you have it) works as intended. VCDS cannot do this however.Guys anyone understand or attempted this?
Guys anyone understand or attempted this?
https://www.dropbox.com/s/b15ymo40ahucl3b/2020-01-01 21.07.11.jpg?dl=0
It’s [08] Auto HVAC
Bit 6-7 - 00 Back Pressure and Recirculated Kinematics Flap Motor for Air Recirculation air flop flap.
there is another option “40” instead of “00”
anyone know what it does??
At a guess, cause I have no idea what this would do, this would tell the HVAC what type of installation and supporting hardware it has.How about this? Anyone?
You went in to long coding, alarm beeps are configured in adaptations. Suggest you do some further reading before jumping in so as to not mess anything up as you have already clicked on the wrong option for what you wanted. Start by creating a backup of your factory / original settings.So I decided to go out and code my alarm beep tonight. Didn’t get past first base unfortunately. Went to the vent elect module, but vcds comes up with
“coding is NOT supported by this control module variant. Replacement modules must be parameterised by using the factory tool and software-version-management (SVM).”
the car is a 2017 s3 saloon. I presume that the later modules are no longer able to be coded with vcds? I did have a search of this thread but didn’t have much luck, so apologies if it’s already been covered.
Also, those of you with VC that have coded the g meter. Does it have to come with the non functional power and torque gauges, or can you enable without them?
You went in to long coding, alarm beeps are configured in adaptations. Suggest you do some further reading before jumping in so as to not mess anything up as you have already clicked on the wrong option for what you wanted. Start by creating a backup of your factory / original settings.
Things have moved on from long coding, with newer platforms it’s more about adaptations.Oh, what an idiot. Thank you. Everything I’ve ever made changes to on vcds has been in coding so I went straight there to look. Last thing I done was a trailer module on my a4 and was amazed just how many different things had to be altered before it would work properly.
i know not to touch anything I don’t understand, just went in for a look about but the advice is still appreciated.
That’ll teach me for not reading the instructions.
Alix whilst I have your attention, do you know if it’s possible to add the combined cruise control/limiter stalk to the s3? I’ve seen it on a TT Of the same era, and it’s something I really miss from driving BMW’s.
Things have moved on from long coding, with newer platforms it’s more about adaptations.
In theory speed limiter should be possible as I have seen the settings but finding the correct compatible stalks might be an issue.
via Adaptations in 09. Have done mine but cannot remember whats needed off the top of my head. Will work it out.I was able to disable my headlight washers totally in 09 central electrics, long coding in vcds in my prefl A3. I now have a fl rs3 but my BCM is just full of zero’s and isn’t readable. Because of this I am unable to disable my useless headlight washers....is there any other coding or adaptions to disable or change how fast the activate? Can you help @DJAlix
enabled g meter power torque
So does the power meter work as intended? I've heard people talking about it not working on the S3.
I didn't do anything differentSo does the power meter work as intended? I've heard people talking about it not working on the S3.
enabled g meter power torque
I didn't do anything different
I did it with obdeleven and it worked !!!