Khufu
Registered User
Nice ! All you need now is one of those little LED Audi torches to go in your cigarette lighter !!
ive just got the white 12v socket light to replace my red one, a torch would look better than the cigarette lighter!
Nice ! All you need now is one of those little LED Audi torches to go in your cigarette lighter !!
Finally hooked up the cable for wireless charging, and retrofitted HHA... But guess I have the US version VC, instead of parking brake icon, I get "PARK"...
How did you hooked up the wireless charger? I have the pinout for the connector but I haven't had access to the wiring diagram yet. I saw that the pinout for the wireless charger is:
pin1:+12v,
pin2&3: to the the MIB unit(one is for Switch On signal and one for Status signal),
pin4: GND,
pin5: to Central Electrics Module -j519- (or to the keyless entry module if the car is equipped with KESSY?).
The first 4pins are quite obvious, but to which Central Electrics pin needs the last wire to be connected? Any idea of the purpose for this wire... maybe it enables the charger while the car is opened?
View attachment 189619
Finally got round to fitting this properly with a converter from trups to convert standard bulb connector to led connector and using a genuine Audi led lamp.
A bit sad but everything else was led out the factory apart from glovebox light. Was annoying my ocd.
mean to do it myself now that ive fitted the LED interior lights.
How did you hooked up the wireless charger? I have the pinout for the connector but I haven't had access to the wiring diagram yet. I saw that the pinout for the wireless charger is:
pin1:+12v,
pin2&3: to the the MIB unit(one is for Switch On signal and one for Status signal),
pin4: GND,
pin5: to Central Electrics Module -j519- (or to the keyless entry module if the car is equipped with KESSY?).
The first 4pins are quite obvious, but to which Central Electrics pin needs the last wire to be connected? Any idea of the purpose for this wire... maybe it enables the charger while the car is opened?
R265 T6a/2 - J794 T12d/5
R265 T6a/3 - J794 T12d/11
R265 T6a/5 - J519 T73c/14
ive just got the white 12v socket light to replace my red one, a torch would look better than the cigarette lighter!
i bought it from TPS but you can buy direct from Audi.Hi sorry to disturb you, just enquiring where did you get the 12 v white light to replace your cigarette light? I want to replace my red one as well
Fitted 5 mm unbranded spacers to the front and got some slight vibration again. I said "again" because I tried using these spacers on my old car and they vibrated that time too. What did I expect? Sadly, there are no narrow spacers (3-6 mm) that wouldn't cause vibration.
May be true. I used these spacers on all corners of my old A3 Sportback and there was vibration. It almost gone when I removed the spacers from the front axle. My theory is that the front axle hub is a couple mm shorter (12 mm) than the rear one (14 mm) and while the rear one is long enough to support an oem wheel with 7 mm wide bevel, the front one is too short and the wheel is held by the lugs only, without any hub support. But that applies to the oem rims. My current rims are replica with the 66.45 mm centre bore and I use spigot rings of 66.45-57.1. The spigot rings have the same wide bevel as the oem rims, so nothing supports the wheel in the middle. I received a new set of the spigot rings with very narrow bevel which in theory can offer more support, so I'm going to try them this weekend.I got 5mm Japan Racing spacers on the rear without any problems (0-250km/h tested). So maybe it’s because it’s the front axle and smaller vibrations will be easier to feel.
So, what did I do today? Ehm I drove my S3 home to a friend of a friend to take a look at the beauty below (it's ontopic now! )
Somehow Jenson Button's former 2005 VIP marked Ford GT40 has ended up in Denmark.
I know it's not Audi related, but I just had to share this with you guys
https://www.evo.co.uk/news/18828/jenson-buttons-old-ford-gt-is-up-for-sale
View attachment 189453
View attachment 189454
Where did you get the center console pieces from? I have been looking for these in red.Went for a new gear stick with red stitching and some centre console knee trim pieces.
View attachment 189940 View attachment 189941 View attachment 189942 View attachment 189943 View attachment 189944
Second hand from ebay mate.Where did you get the center console pieces from? I have been looking for these in red.
Excellent job . Feeling your pain with the masking tape...that would of took some time to get that done correctly, which you have. What tyre dressing do you use?Sorted out the rusty hubs
Sent from my SM-G973F using Tapatalk
Excellent job . Feeling your pain with the masking tape...that would of took some time to get that done correctly, which you have. What tyre dressing do you use?
Spot on Tash. Can see the difference immediately. Bet that was an expensive checklist Nice trip great the handling is better too . Such an improvement on those archesCambelt Replaced
Front Discs and Pads
Lower Rear Linkage Arms
Top Mounts
Lowered on Eibach Pros
Before
After. I know it still take a little while for the springs to settle, the difference in handling in night and day, it is more planted and nice firm ride.
Spot on Tash. Can see the difference immediately. Bet that was an expensive checklist Nice trip great the handling is better too . Such an improvement on those arches
I'd love to do that to mine looks about the same or worse!! A quick guide ? I have no clue lolSorted out the rusty hubs
Sent from my SM-G973F using Tapatalk
I believe there's a sticky in the detailing section for it from Scotty I believe!I'd love to do that to mine looks about the same or worse!! A quick guide ? I have no clue lol
Sent from my SM-G973U using Tapatalk
I'd love to do that to mine looks about the same or worse!! A quick guide ? I have no clue lol
Sent from my SM-G973U using Tapatalk