- Joined
- Apr 25, 2016
- Messages
- 3,321
- Reaction score
- 3,180
- Points
- 113
One of the best I've seen.
One of the best I've seen.
I’m sitting down so how much were they?
Just removed my OZ Daker 20x9 ET45 with 235/30 Conti Sport 6 all round (Now for sale), and fitted OZ Leggara HLT 8.5x19 ET38 - No spacers required - Running Conti Sport 5 255/30 and 235/35. These wheels withoutt yres are under 10kg each!
I dont think the pictures do these wheels justice - Well pleased with them
Anyone tried the 19” golf R Pretoria wheels on the RS3 ? Always liked them personally
Anyone tried the 19” golf R Pretoria wheels on the RS3 ? Always liked them personally
Suppose it's for Sportback, if I'm not wrong, Golf R Pretoria has ET49. Same as RS3 Sportback. But they would not work for Saloon, you will need spacers to fit.
stunninghttp://forums.m3cutters.co.uk/showthread.php?t=163649&page=2
Pages 2 and 3. I bought a set for my 8P RS3 after seing this and they looked spot on but not tried them on my facelift yet.
i really like them
Not far off - 19inch prets are ET50
Sent from my iPhone using Tapatalk Pro
They're only 8J too, aren't they? Would need 12mm spacers to sit nicely.
I got a set of Performanceline R360 wheels, 19" ET44 8.5" and had them powder coated in a matt anthracite finish. Was hoping to go to a square setup using 255x30x19 PS4S tyres, but alas there has been some issues!
Main issue is clearance for the front calipers. Rears sit perfectly with no spacers fitted. The front however don't clear the calipers, even with 5mm spacers. I have 8mm hubcentric H&R spacers but the hub profile is different. The H&R spacers have quite a big angle on them, although they do fit the Audi alloys, they don't fit the R360's. The angled recess for the hub on these wheels is very shallow, which results in the spacers not seating fully home. Unfortunately there is a gap of approx 4mm between the spacer and wheel.
Considering what to do now... machine the R360's so they fit the H&R spacers, try different wheels, remain with the standard staggered Audi wheel with 235 tyres to the rear, or try to find 2x 8.5" alloys for the rear and fit the 255 PS4S tyres all round....
I was told by Ispiri that the FFR1 ET 37 do not require spacers.Any 8.5s that dont need spacers ?
OZ Formula HLT’s fitted yesterday
View attachment 162923
Is it possible to get 3mm black hubcentic spacers does anybody know... I think they would bring them out perfect
Very very nice mate
Seems like you've purchased H&R spacers that fits OEM wheels, you need the other version that fits after market wheels.
I use 10mm front and 12mm rear H&R spacers, and my wheel are exactly the same offset as yours.Harith you mentioned you used 5mm spacers and got the R360 wheels to fit. What offset are your wheels? What spacers did you use?
OZ Formula HLT’s fitted yesterday
View attachment 162923
Is it possible to get 3mm black hubcentic spacers does anybody know... I think they would bring them out perfect
I was told by Ispiri that the FFR1 ET 37 do not require spacers.
Ok. Mine arrived yesterday so will try them tomorrow and if they don’t they are going straight backI was told this by them also... and they do require 5mm spacer to clear the calliper and also spigot rings which they said shouldnt be required. Also had a nightmare balancing them as the 5mm bimecc spacer i had was hubcentric but do not extend the lip and still had a slight judder, 10mm h&r hubcentric with hub lip seems to do the trick although it pushes the tyre out more than i wanted
Ok. Mine arrived yesterday so will try them tomorrow and if they don’t they are going straight back
I have the sportback so let’s see....Good luck! Should also point out i have the saloon, the backs fit perfect but the fronts lock hard to the calliper, and still have the slightest of judders at 70mph with 10mm h&r’s and alu spigot rings, cars going in on wednesday for a balance check and geo to make sure everythings good that side of things... then not sure what to do!
Good luck! Should also point out i have the saloon, the backs fit perfect but the fronts lock hard to the calliper, and still have the slightest of judders at 70mph with 10mm h&r’s and alu spigot rings, cars going in on wednesday for a balance check and geo to make sure everythings good that side of things... then not sure what to do![/QUOTE
I just took the front let wheel off and put the rim on and they look like they do clear the calipers. I only ran the rim around against the holding plate and didn’t do them up but fingers crossed they fit!! Too wet
Fitted all ok without the need for a spacer.
Fitted Neuspeed RSe102 19x8.5 ET 45 alloys this week with staggered 255/235 P-Zeros. No spacers and plenty of space between spokes & front callipers.
View attachment 164204
Thanks. Got it looking exactly how I want it now. The drop on H&R springs is just about perfect for me and bonus is that there are no rubbing issues.They look scary OEM lol....that looks superb mate, lovely!!!!!!