Search results for query: *

Hey, What engine code do you onw mate? I always use impact gun to remove the crank bolts, there is no need to hold anything that way. There is some play in the diff abut not sure what play is allowed. No I`ve used my old joints as there where ok, just sandblasted them and painted. The clunk...

I understand that china can and do make good quality parts. I`ll most likely go with bager5 H or I beam rods are rather spend a bit extra and forget about it. Regarding pistons i was planning to stay with oem as not planning to get above 500hp, however if i can find a set in a good price I`ll...

Hey, The uprights and all the brakes are sorted now mate, thanks anyway. I just did not have the time to post any updates, there was a lot happening, stripped the engine, realised that I need another block. So got an AWT from a passat with 06A block. Need all intake side brackets if anyone got...

Try local scrap yards mate, what do you need?

I'll do that for you. You'll be surprised how quiet it is mate with the catt on and one small silencer.

Hi. Im afraid that this is a custom made so the guy making it won't be able to say exactly what bends he did make. I should be picking te car up today so I can run the lengths with tape measure but measuring the bends is always tricky. There is couple of things I'm not 100% happy with...

I still haven't pick it up but got some photos already there for you.

Hard to say but if you 100% sure the diff is dead then makes sense to replace it and ask the person to go through the diff suspension. Good luck

Hey, sounds like diff carrier bushes or the support bush on front of the diff is gone, will it make the same bang on quick gear change?

No worries, 3inch mate

Hi, i`m not an expert but as far I know best is 314 ss grade, the wall should be around 1.5mm. I`ll be picking up my car from exhaust fabrication bloke, if you dont mind waiting till weekend I`ll send you a pictures of mine one when is done

I'm relatively new here so don't what use to be like but is seams little quiet. I've spaced out one of the adapters for now. Those hubs should have a part number on it but not those ones. Not to worry, I'll get there in the end. Thanks

Attaching some photos of the fitment Right side: Right side sits perfectly Left side: As you can see the l;eft side is off by few mm. Ignore the fact that the caliper is upside down. Any info regarding the front wheel hubs much appreciated. Cheers

Hi there, I have collected all the components to fit Brembo 18z calipers. When tried to fit them i run into a bit of issue. One of the calipers fits perfectly and sits right in between the rotor (left side) when the right caliper when mounted is resting against the rotor. We are looking for...

The biggest trouble it will be the access to it. Very fiddly job in there.

Yes, they should be another drain on the other side mate. Doesn't look good in there, hopefully is only surface rust.

Good luck with the project mate, Ill be following

Hi guys, I think is time for a bit of update. Managed to get the middle and rear floor done, is a shame that I cant do it all in one go but well. There was also a bit of rust by the cabin filter as well. Ill tackle the engine bay next year went the engine will be out for rebuild...

I had a look in Poland for it, it doesn't look promising but send an couple of emails to ask for availability, I have a bit of hope on this side... https://www.iparts.pl/czesc/podkladka-oem-431501219,1-3015-431501219-1952533.html I'll let you know as soon as they reply mate. By the way, grate...

Hey. Is this number 6 on the chart? http://www.oemepc.com/audi/part_single/catalog/au/markt/ZA/modell/A4/year/1998/drive_standart/218/hg_ug/500/subcategory/500020/part_id/706342/lang/o