Search results for query: *

Hi looking for some help from the Audi gurus. Yesterday my girlfriends car (2011 mk2 audi TT 2.0TFSI) had issues. The car was misfiring and only running on 3 cylinders at most. There was intermittent, light coloured smoke from the exhaust (mainly on acceleration) Once the car was off, I went...

Hello, I was wondering if it's possible to clone a ECU chip by reading it and burning the information onto a new, blank chip. If so; what hardware and software would be suitable to do this? I'm specifically interested in doing this to an AGU model ecu... so i understand the chip will need to...

What are the best spark plugs to use when running much higher boost than stock ( and what size gap)?... Also, I'm going to be sending my car to a garage to check and repair any boost leaks. Would I be better off finding a garage with a smoke tester or with just a basic pressure tester? Anyone...

Found this quite interesting. Wasn't expecting the results...

Hey just received my fmic ebay special edition. It has thread holes on the top of the intercooler itself which looks as if its for mounting. It hasn't however come with any mounting brackets or screws. Looking at other DIY threads, I cant tell how or if the FMIC is being supported or if it is...

Can anybody tell me what the outside diameter is of each exhaust tip is (before it dips down)? Thanks for your help in advance!

Title says it all really... Planning on throwing some notes at my car during the winter period after all the fun its given me over the year. I will definitely be going down the big turbo route, quite interested in anyone's set up which is seeing past the 300hp ball park. Pics would be nice...

Just installed larger injectors into my AGU. Everything was running nice and smooth for a good few hundred miles/ few days until last night a severe flat spot problem occured. Its still holding/creating boost fine during the flat spot but it has barely no power until it kind of splutters and...

Hello, Just wondering if it is possible to remove a K03 turbo from the top of the engine bay? This sounds more appealing to me than spending my Saturday underneath the car. Has anyone got any preferred methods of removal who have done it more than once? Your help is appreciated as...

Hello, I have just purchased a direct replacement (K03) turbo. I need to fit it this weekend as it's important my car is up and running for a trip of Monday. What will I need to buy along side to fit the turbo as id like to have it all collected from the Audi dealer in advance? (Gaskets...

https://www.youtube.com/watch?v=i6GGk7FUNxc&feature=youtube_gdata_player Ive been having an on going problem with boost on my AGU. To start with the car has the following modifications ( I understand some are frowned apon here) *boost controller *3" down pipe * 4 bar fuel regulator...

Hello, Just wondering if anyone can help. I was trying to install a performance chip on my ECU (AUG) and I have made a right mess of it. Once I installed it, the car would turn over but wouldn't start. I decided id remove the performance chip and replace it with the cars original. In doing so...

Ive just finished changing the clutch on my car but I have encountered a problem. The driveshaft is short of the gearbox by about half an inch on the drivers side. The engine seems to be mounted to the far right of the car as possible already. . Not sure of my options from here? Can anyone...

I can see the timing mark on my replacement flywheel but I cant see the timing mark on the engine block. .. where should I be looking? The car is a 1.8t 150. Thanks a lot

Would anyone be kind enough to tell me how many bolts hold the gearbox to the block?

Anyone interested in finishing off a clutch and flywheel change on my 1.8T 150? The box is ready to come off (with some persuading it looks like) with driveshafts disconnected, all bolts have been put back into their correct positions where possible apart from the gearbox bolts obviously. The...

I have bought this slave cylinder and plan to do a clutch change on my car tomorrow. I did not realise that there is two different typea of slave cylinders. My car is a 1998 1.8t 150. Does anybody know of this is the correct replacement part?

Been trawling around the forum looking for a guide on how to remove the gearbox on a 1998 150 model but with no luck. Tomorrow ill be replacing the clutch and flywheel so a "how to" guide would be really handy. Could anyone be kind enough to point me in the right direction? Also, I...

01262-Turbocharger (TC) wastegate regulating valve Wiring, fuse, TC wastegate regulating valve I have noticed at times that the recirculation valve has been fluttering and also sometimes it feels as if all boost has been lost intermittently and then returns a few minutes after. I...

When I install my VR6 clutch and ABF flywheel, am I right in thinking that I would need to install a slave cylinder for an Audi 8L 1.8t or for a VR6? Also, would the "1995" VR6 clutch be the right age and clutch for the ABF flywheel? Thanks in advance.