Easiest way to diagnose is through OBDEleven amd live data.
Or if you have G Meter on on your car see if it has froze or not. When my haldex stopped working my G Meter also stopped ironically.
Sent from my LM-V600 using Tapatalk
Yea it is very easy to do. You are better off breaking the trim below the piece you are talking about off first. It becomes easier because instead of going at it from the side you can do it from the bottom.
You can still remove the piece you are talking about from the side it just ends up being...
There are U-clips that fasten that particular trim piece to the car. Sometimes they can break loose (for me at least) and you can try to push down on those sections of the trim that have the U-clips attached and see if the creaking goes way.
That whole trim piece is almost complete plastic so...
Hello!
There has been much talk about this topic and I wanted to see if there was a consensus in the community regarding this topic. I know version numbers have been changing so I felt it was appropriate to create a brand new thread in order to document any changes.
1. What is the latest...
I use the USP Motorsports Tear Duct Air Filter.
Gets the job done and for a good price. Only issue is that it doesn't sit perfectly flush to the air inlet by the bumper. I wish that is something they have changed now.
Sent from my LM-V600 using Tapatalk
I got you.
I have the electrical diagrams for that connector that I used from a document I own myself.
I used it to wire the door treble speaker and the band olufsen light.
PM me your email and I will send the whole packet of stuff to you.
I have tons of packets and documents that will be...
VERY easy job. The plastic trim is the hardest part. The seat DOES NOT have to come out in order to install and reinstall. Just make sure the battery is connected and is moved AWAY from the triple square bolt to make it easy to get to. The bottom trim comes out first and then take the middle...
I'm going to get mine painted or something. The vinyl that is cut is never cut correctly or cut at the right size.
Sent from my LM-G710VM using Tapatalk
My sunroof creaks as well. Does anyone know what causes it?
I never go to the dealer. I fix everything myself usually. Just haven't given this one much thought really.
Sent from my LM-G710VM using Tapatalk
So I had this fault awhile ago.
It was a different code though.
The airbag sensor is located to the right and left of the rear seats. The plastic trim where the seatbelt comes out of [the front piece, I can show it WAY more clearly later if you like].
I am sure you have tried clearing the...
The dark ones make the little rectangle/rhombus looking cutout in the mirror hard to see in daylight. It looks aesthetically better but, I got the ones that aren't smoked out and the light is brighter and looks nicer IMO.
Sent from my LM-G710VM using Tapatalk
I live and die by Liquimoly. They made noticeable improvements as far as engine oil is concerned. Better idle, a LOT LESS oil consumption, and the added benefit of spotting leaks more easily.
I have not noticed any difference in the gearbox fluids and I really do feel anything will do as long...
If you have photos that would help.
One concern would be regarding the suspension. I would be led to believe that there is something creating negative camber? Do both rear tires show the same wear on the inside? I would imagine that the owner would have sent it to have an alignment done at this...
We need to know your torque numbers.
I have the DQ250 unit and it's rated for up to 400nm. Obviously people here have increased theirs substantially so one can assume that these measurements are conservative.
The DQ381 from a random website said 435nm and other figures are +/- 10nm. I know...
I see.
The "camera" above it, is that used only for Audi pre sense? I believe you can do traffic sign detection as well if I am not mistaken.
Sent from my LM-G710VM using Tapatalk
Does it manually open however?
I had the same exact problem. In extreme temperature changes the black plastic retainer for the locking actuator broke. It would literally not open no matter how hard I tried because the right angle fork could not pivot 90 degrees towards me. It would go like 35...
Stupid question but, do you need extra hardware in order to get high beam assist to work or can you get it to work via VCDS/OBDEleven?
Sent from my LM-G710VM using Tapatalk
I have the full electrical diagrams for practically everything.
Let me know if you need it. It is VERY comprehensive.
Sent from my LM-G710VM using Tapatalk
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.