Hi forum,
Hopefully somebody can shine some light on this.
I would like to hook-up 2 Focal amps (2 channel for the front, 3 channel for the back & sub)
There for I need to find the line out's of the RSN E MKII, below I marked the pin numbers.
Section B
3 - Line Out FL (front left audio signal)
5 - Line Out RL (rear left audio signal)
8 - Line Out GND (audio ground)
9 - Line Out FR (front right audio signal)
11 - Line Out RR (rear right audio signal)
So far it seems straight forward 4 line-out's(+) and 1 line-out GND (is this a common(-) for all 4 line-out's ?)
What happens with the amplified front speakers when I want to use the line-out's only, do I have to terminate them?
Section D
13 - U14 ST DSP (Radio On) (remote âonâ lead for rear amp)
I believe this one is to switch on the amps (the main + will be separate, fused from the battery)
Quadlock connector (http://bublin.eu/car/rns-e diagram.pdf)
B. EXT Control Connector (CD Changer, PhatBox,
OEM SAT tuner etc.) (Female pins/wires: #000-979-009)
1 - Most Ring break (NC)
2 - CDC-NF GND (audio ground for CD changer)
3 - V-Signal (analog speed signal/GALA)
4 - U14R-2 (Constant power source for CD changer etc)
5 - K-Line (K-line diagnostic; VAGCOM)
6 - CDC-Data out (CDC data out)
7 - BOSE Pin (used if you have a Bose system)
8 - CDC-NF L.IN (cd changer left audio in)
9 - CDC-NF R. IN (cd changer right audio in)
10 - U14 ST CDC (Ignition/accessory power for CD changer)
11 - CDC -Data IN (cd changer data input)
12 - CDC- Data CLK (cd changer clock input)
A: Speaker Connecter (front passive speakers) Not to be used with amps
(Female pins/wires: #000-979-133)
1 - N.C.
2 - Right Front (+) not used with amps
3 - Left Front (+) not used with amps
4 - N.C.
5 - N.C.
6 - Right Front (-) not used with amps
7 - Left Front (-) not used with amps
8 - N.C.
C: EXT Control Connector (For Bose or
Non-Bose Amp, telephone interface)
(Female pins/wires: #000-979-009)
1 - *MIC IN (-)
2 - RFSL (Analog reverse signal)
3 - Line Out FL (front left audio signal)
4 - *MIC Out (-)
5 - Line Out RL (rear left audio signal)
6 - TEL NF IN (-) (Telephone speaker negative input)
7 - *MIC IN (+)
8 - Line Out GND (audio ground)
9 - Line Out FR (front right audio signal)
10 - *MIC Out (+)
11 - Line Out RR (rear right audio signal)
12 TEL NF IN (+) (Telephone speaker positive input)
D: Power Connector (Female pins/wires: #000-979-133)
9 - CAN-H (CANbus High signal)
10 - CAN-L (CANbus Low signal)
11 - TEL-Mute (Telephone mute connection)
12 - Kl.31 (Primary ground connection)
13 - U14 ST DSP (Radio On) (remote âonâ lead for rear amp)
14 - DWA-GND (Alarm ground)
15 - Kl.30 (Constant 12V power source)
16 - U14R-1 (N.C.)
I am planning if I can use the line-out's to get a male and female Quadlock connector and wire them accordingly so I don't have to cut the original loom or is it possible to remove section C and just buy that part, that brings me to the next question.
Where can I buy a a male and female Quadlock connector and or just the sections online?
Thanks in advance,
Rick...
Hopefully somebody can shine some light on this.
I would like to hook-up 2 Focal amps (2 channel for the front, 3 channel for the back & sub)
There for I need to find the line out's of the RSN E MKII, below I marked the pin numbers.
Section B
3 - Line Out FL (front left audio signal)
5 - Line Out RL (rear left audio signal)
8 - Line Out GND (audio ground)
9 - Line Out FR (front right audio signal)
11 - Line Out RR (rear right audio signal)
So far it seems straight forward 4 line-out's(+) and 1 line-out GND (is this a common(-) for all 4 line-out's ?)
What happens with the amplified front speakers when I want to use the line-out's only, do I have to terminate them?
Section D
13 - U14 ST DSP (Radio On) (remote âonâ lead for rear amp)
I believe this one is to switch on the amps (the main + will be separate, fused from the battery)
Quadlock connector (http://bublin.eu/car/rns-e diagram.pdf)
B. EXT Control Connector (CD Changer, PhatBox,
OEM SAT tuner etc.) (Female pins/wires: #000-979-009)
1 - Most Ring break (NC)
2 - CDC-NF GND (audio ground for CD changer)
3 - V-Signal (analog speed signal/GALA)
4 - U14R-2 (Constant power source for CD changer etc)
5 - K-Line (K-line diagnostic; VAGCOM)
6 - CDC-Data out (CDC data out)
7 - BOSE Pin (used if you have a Bose system)
8 - CDC-NF L.IN (cd changer left audio in)
9 - CDC-NF R. IN (cd changer right audio in)
10 - U14 ST CDC (Ignition/accessory power for CD changer)
11 - CDC -Data IN (cd changer data input)
12 - CDC- Data CLK (cd changer clock input)
A: Speaker Connecter (front passive speakers) Not to be used with amps
(Female pins/wires: #000-979-133)
1 - N.C.
2 - Right Front (+) not used with amps
3 - Left Front (+) not used with amps
4 - N.C.
5 - N.C.
6 - Right Front (-) not used with amps
7 - Left Front (-) not used with amps
8 - N.C.
C: EXT Control Connector (For Bose or
Non-Bose Amp, telephone interface)
(Female pins/wires: #000-979-009)
1 - *MIC IN (-)
2 - RFSL (Analog reverse signal)
3 - Line Out FL (front left audio signal)
4 - *MIC Out (-)
5 - Line Out RL (rear left audio signal)
6 - TEL NF IN (-) (Telephone speaker negative input)
7 - *MIC IN (+)
8 - Line Out GND (audio ground)
9 - Line Out FR (front right audio signal)
10 - *MIC Out (+)
11 - Line Out RR (rear right audio signal)
12 TEL NF IN (+) (Telephone speaker positive input)
D: Power Connector (Female pins/wires: #000-979-133)
9 - CAN-H (CANbus High signal)
10 - CAN-L (CANbus Low signal)
11 - TEL-Mute (Telephone mute connection)
12 - Kl.31 (Primary ground connection)
13 - U14 ST DSP (Radio On) (remote âonâ lead for rear amp)
14 - DWA-GND (Alarm ground)
15 - Kl.30 (Constant 12V power source)
16 - U14R-1 (N.C.)
I am planning if I can use the line-out's to get a male and female Quadlock connector and wire them accordingly so I don't have to cut the original loom or is it possible to remove section C and just buy that part, that brings me to the next question.
Where can I buy a a male and female Quadlock connector and or just the sections online?
Thanks in advance,
Rick...
Last edited: