Search results for query: *

is it similar to this sound??

My ecu was destroyed due to water damage

Hi everyone, i hear this clicking sound only when exist loads the road is grippy and i have to turn the steering wheel fully left then fully right and the clicking noise appears when i put the steering wheel from right to straight ahead. I’ve already check the inner tie rod from steering rack...

Is the number 8 the magnetic clutch? Is it make any sense to regass the system?

Hi everyone, I hear a strange noise when the a/c is on and the noise is increased when the revs are increased, when I press the “AC ” button the sound stops. When I decrease the temp of the climate the noise also is reduced. This happens only when “AC” is on, here is pic while ac was warking:

Hello everyone, I’m in need of changing my ABS unit from my MQB, I’ve just found one used and I would like to avoid the online coding as i don’t know from where that unit come from, so that I would like to ask if there is any way to avoid online coding..thank you very much

After I had serviced my rear magnetic ride shocks and had renewed bump stops not the top mount as well as they were in perfect condition, i hear a noise, after checking i saw this: The bump stop are moved from its position which is in top mount. Any suggestion??

I have an audi s3 8p with 70k km completely stock, after a dsg service oil and filter change, I ‘ve already driven it for 500km and I realized a little slip with 1-3-5 gear, then I was sure my trans heat exchanger had failed. Is there any way to completely drain this mixture or some way to...

thanks for the answer, my car is completely stock, so that i don't this that the box can not handle the power, before changing the oil i noticed the oil filter cover was leaking, so that i proceed in an oil change, i don't know if it is a mistake to drain the oil when it was cold and the car...

Hello everyone, I have an audi s3 8p 2010 s-tronic completely stock with 70k km. I had slipping issues with 6th gear and 4th gear and a little noise during the slipping. I had an oil and filter change(100% genuine products) and after that I have done a basic setting. After that I have the same...

Maybe I have to change the fluid and also check the fluid level

Do u have the same oil in dsg for 200k miles??

Suddenly the car is a little strange. It is competely stock with 70k km and is slipping with 6th gear. While driving with 2.200 rpm the rev counter starts revving in 2.400 or 2.600 and the go back in 2.200 rpm(slipping). I have not changed the oil and the filter yet but I have done basic...

Ok, thank you very much for your answer, I measure directly from the battery (-) with the multimeter, and i notice this issue, when i disconnect the quadlock connector from rns-e the current is 0.04, also there are lots of references tha “Traffic Program” drain the battery.

Hello everyone, I discovered that my factory-fitted rns-e with bose sound system is destroying my battery. I have measured the current and it is like a pulse, in my multimeter I can see 0.04-0.22-0.35-0.04…. And it doesn’t stop, I also I don’t have fault codes and also i don’t have bluetooth or...

Hi everyone, my car's ecu suddenly died, so that i have a problem with the correct file, I need an original flash file. My car is an audi s3 8p 2009 s-tronic with magnetic ride. ECU part number: 8p0907115ab with software 0010. If anyone had a stock file please send it to me asap.

Hello, i have suddenly a very strange problem, when i tried to start up the car, the engine didn't start but the starter motor works normally. In addition the cooling fan starts working to maximum power with the ignition on. I checked with VCDS and i noticed there is no communication with ECU, I...

can you send me a link? I don't have access to official erwin

Hello everyone, i'm on the way to retrofit adaptive bixenon to my s3 8p facelift, my car has 4 lever sensors because it has mag ride. Except from adaptive headlights and the j431 module, is there anybody who knows exactly the wiring adaptation, i think changes should be done in connecter 14c...

No problem, you weren't clear, i asked WHERE exactly are the adjustment points. etc from where EXACTLY can i adjust my bumper?...many thanks for answering!