nvm. i found my answer.
Anyone running updated firmware of jb4?
Sent from my HTC 10 using Tapatalk
There’s a new firmware? R u sure?
Thanks for reply!Map6 at 26psi peak
Thanks for reply!
Are You using auto clear for O2 sensor CELs?
Anyone experienced problems with the haldex unit? I'm asking because the additional stress on the clutch plates may wear them prematurely and thus contaminate the oil in the unit and blocking the filter.
My question arose after reading this thread: http://www.audi-sport.net/xf/threads/check-this-out-haldex-pump.348155/
(I know @RedS3Reilly is runing almost twice the stock power but I just thought I would hear other peoples experiences with haldex and JB4)
Stay away from launch control when using a tuning box as that’s when the most stress occurs from my experience since the gearbox doesn’t read true torque levels etc. When running more power than stock more stress will be put on the Gearbox,transfer box and haldex unit. With regular maintenance and respecting the car, you shouldn’t experience any issues.
Regarding the launch control; could you get around this by putting 0 psi boost in an additive map6 in 1st gear and maybe 3 psi in 2nd and then unlimited in all other gears?
That wat i do for not putting load on first/2nd gear...... 0.1 on max boost on 1st and 2.0 or 3.0 on max boost 2nd.
Regarding the launch control; could you get around this by putting 0 psi boost in an additive map6 in 1st gear and maybe 3 psi in 2nd and then unlimited in all other gears?
The car only runs a small amount of boost in 1st. The issue is my map 6 is asking for 24psi about double what I've seen. Dropping the 1st gear boost to 3 psi over stock or say 16 psi depending on air temp still gives extra power but doesn't upset launch controlYou could limit boost in gears 1/2 but then that would be limiting the amount of power surely ? I did a 3k launch awhile back instead of 4.5k by feathering the throttle and it launched off cleanly and hard.
Hi all,
I have a JB1 installed on my 2015 S3, but for the life of me cant get the software installed on my laptop. I have been in conversation with George from Burger Motorsport but still no luck...think my laptop is knackered.
Is there anyone based in the South London area that would be able to help out at all? I'm keen to get some logs over to George and change to a bespoke Map 6.
Any help would be greatly received.
Hi all,
I have a JB1 installed on my 2015 S3, but for the life of me cant get the software installed on my laptop. I have been in conversation with George from Burger Motorsport but still no luck...think my laptop is knackered.
Is there anyone based in the South London area that would be able to help out at all? I'm keen to get some logs over to George and change to a bespoke Map 6.
Any help would be greatly received.
I had the same issue when i had a jb1, i had to change something in the laptops settings before it would work but i was speaking to george on facebook at the time and he talked me through it, think i sent him a few pics and he guided me through it all
I'm in the west midlands but it should work on any laptop with usb.
Other option is use an Android phone, I use my S8 with a USB-C to USB-A adaptor and it works a treat
It's really annoying. I got to the point where I had the JB4 program on screen, but couldn't identify the unit through the laptops com ports.
The laptop is an old work one and is now decommissioned, so I'm up s**t creek with zero paddles now!
Thanks for the reply. Any idea if it works with iPhone?
Try to add a new user on your laptop and then install it. For some reason, I couldn’t install it as well until I created a new user.
Seems like u have to change the com port to 3....hope this helps but its the only screenshots i had from when i had the problem