VCDS Mod list ? Do we have one ?

[Anthony566]

Hi do we have a VCDS Mod list like this one ?

Enable Hidden menu in MMI

Adjust bluetooth microphone sensitivity
Change MMI 3G splashscreen
Disable After-wipe of windscreen wipers
Disable amber corner lights
Disable amber side markers
Disable Key warning (keyless models)
Disable LED 'wink' on turn signal - pre-facelift
Disable LED 'wink' on turn signal - facelift
Disable bulb error message with LED reverse lights installed
Disable "Lights are on" warning
Disable NAV & Phone warning messages while entering data at speed
Disable Seatbelt Chime
Disable soundaktuator (speaker on face lifts)
Enable Adaptive brake lights
Enable Ambient Interior Lighting Control
Enable Optic rear parking for cars without front parking sensors
Enable Automatic Gear selection shown in DIS
Enable Automatic Hill Hold Assist 'lite'
Enable Auxiliary ventilation
Enable Battery meter *does not appear to work on facelift cars with MMI 3G+ HDD Navigation*
Enable DIS with Efficiency Program
Enable Double Disarm Beep
Enable Drivers Memory Seat
Enable DRL Selectable via MMI
Enable DRL
Enable Audi Drive Select without the buttons
Enable Euro parking lights that turn on signal at night
Enable interior lighting option
Enable fog lamp to come on for the same side as that turn signal
Enable Front Turn Signals as Parking lights
Enable Gauge Test/Needle Sweep
Enable Import CDs to MMI's HD
Enable Independent Fogs control with high beams
Enable Lap Timer
Enable LEDs remain bright for parking lights
Enable Rear Tail Lights on with DRLs
Enable Release Parking Brake without putting foot on Brake
Enable Release Parking Brake without putting seatbelt
Enable Remote Operation windows&sunroof
Enable Reverse mirror tilt
Enable Speed through MMI
Enable ‘Tourist’ Mode – Headlight Convertor (MMI 2G)
Enable TPMS (Tyre Pressure Monitoring System)
Enable Video in Motion on MMI
Set Audi parking system - Switch OFF Speed
Set Custom ADS settings
Set Headlight washer - cycles
Set Headlight washer - duration
Adjust Consumption in DIS
Adjust LED Brightness
Change Language
Activate SDS for cabriolet
Change fuel tank characteristics
To increase radio play time after car is turned off

Audi A4/S4/A5/S5 B8
VCDS (VAG-COM) codes


Enable Hidden menu in MMI 3G

[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1

To access the hidden menu, hold down car and setup together for 5 seconds

Use this hidden menu at your own risk.



Enable Hidden menu in MMI 2G

[07 - Control Head]
[Adaptation - 10] -> Channel 8 -> Change 0 to 1

To access the hidden menu, hold down car and setup together for 5 seconds

Use this hidden menu at your own risk. Caution: Keep away from the "Bootloader"
________________________________________

Adjust bluetooth microphone sensitivity

Hidden menu
Diagnose
Settings
Mic sensiblity - choose -6db/0db/+6db

________________________________________

Change MMI 3G splashscreen...

Enable through the "hidden menu":
- navigate to 'car/carcodingvehicle'
- choose the model of choice in 'configuration line'
- select 'Update Splashscreen'
- restart MMI

________________________________________

Disable After-wipe of windscreen wipers

[09 – Cent. Elect.] [Coding - 07] -> [Dropdown] -> "x ** 8K1 955 119 ** WWS xxxx" -> Long Coding Helper -> Byte 1
Bit 3 - Remove check mark (1 = active)
________________________________________

Disable amber corner lights

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________

Disable Key warning (keyless models)

[46 – Central Conv.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________

Disable LED 'wink' on turn signal - pre facelift

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 3
Bit 2 - LEDs remain at full brightness with parking lights (1 = active)
Bit 7 - Turn off LED-strip DRLs with indicators (1 = active)

________________________________________

Disable LED 'wink' on turn signal - facelift

09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3 (Heading Wink Brightness)
Default Value is 26, Setting value to 88 (Makes it identical to normal brightness)
________________________________________

Disable bulb error message with LED reverse lights installed

CREE LED reverse lights with RESISTOR and I STILL get a bulb out warning?
________________________________________

Disable "Lights are on" Warning

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 5
Bit 3 - Set to 0 to disable "lights are on" warning when you open the door.
________________________________________

Disable NAV & Phone warning messages while entering data at speed

[5F - Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________

Disable Seatbelt Chime

[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 0
Bit 2-4 – Seat Belt Warning inactive

________________________________________

To mute the Soundaktuator

A9 Structure Borne Sound
Adaptation 10
At Channel drop down choose "Volume of structure borne noise actuator" (only choice)
Enter a value in the proper box (0% = mute )
________________________________________

Enable Adaptive brake lights

[46 - Comfort System] [Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)

________________________________________

Enable Optical rear parking for cars without front parking sensors

[10 - Park/Steer Assist] [16 - Security Access - 71679] do it [07 - Coding] Byte 0 - Bit 4 change 0 to 1
________________________________________

Enable Automatic Gear selection shown in DIS

[02 – Auto Trans] [Adaptation – 10]
Select “Single Gear Display” from top channel drop down menu
Select “D on/S on” from New value drop down menu
________________________________________

Enable Automatic Hill Hold Assist ‘lite’*only works on certain abs modules - see below link*

[03 - ABS brakes][Security Access - 16] (Enter code presented by program)
[Coding – 07] -> Long Coding Helper -> Byte 1
Bit 6 set to 1 to enable hill hold assist.

http://www.audienthusiasts.com/VagComABS.html
________________________________________

Enable Auxiliary ventilation

[5F - Information Electr.] [Coding - 07] -> Long Coding Helper -> Byte 6
Bit 1 – Set to 1
[Hidden menu] [car] [cardevicelist] [Auxiliary heating] Enable
[08 - Auto HVAC] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 – Set to 1
Bit 4 – Set to 1
________________________________________

Enable Battery meter *does not appear to work on facelift cars with MMI 3G+ HDD Navigation*

For MMI equipped cars

[Hidden menu] [car] [cardevextdevicelist] [Battery] Enable
[Hidden menu] [car] [carmenuoperation] [Battery] Set to 5
Reset MMI
or
[56 - Radio] -> Adaption -> Channel 39, add 16 to your value

For symphony, Chorus and Concert

Select module 56 - Radio

Select “Adaptation – 10

Select channel 39

Add 16 to the present value
"test"

"save"

“Done, Go Back” and "Close Controller
________________________________________

Enable DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System)

[17 - Instruments] [Adaptation - 10] -> Channel 77
change 0 to 255
________________________________________

Enable Double Disarm Beep

[46 - Central Conv.] [Adaptation - 10] -> Channel 63
Add 4
ensure Module 46, Byte 1, Bit 2 is ticked. This activates the alarm audible notification option
________________________________________

Enable Drivers Memory Seat

36: Seat Mem - 07 Coding - Long Coding Helper - change Byte 2, bit 0, to 1

Seat memory will be there however greyed out in MMI

Press and hold down unlock button on key fob for 5 seconds for the windows to come down

Press and hold down lock button on key fob for 5 seconds for the windows to go back up

In MMI, Seat Adjustment you are now able to find Driver's seat, you can set Key memory on/off. Set it "on" for both keys separately.
________________________________________

Enable DRL Selectable via MMI

[09 – Cent. Elect.] -> [Coding – 07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1
________________________________________

Enable DRL

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL via Front Side markers
Bit 2 = DRL via High Beams
Bit 3 = DRL via Fogs
Bit 4 = DRL via LEDs
Bit 6 = DRL via Side markers
Bit 7 = DRL via Tail lights
________________________________________

Enable Audi Drive Select without the buttons

By far the best guide is here - http://www.audienthusiasts.com/Project_ADS.html
________________________________________

Enable Euro parking lights that turn on signal at night

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 0 - Set to 1
________________________________________

Enable interior lighting option for pre-facelift

MMI Basic (Symphony/Concert radio) - (NON-MMI - 2G/3G):
Code:
[56 - Radio]
[Coding - 07] -> Long Coding Helper -> Byte 8 Bit 7 - Interior Light Settings active - (1 = active)

MMI high (2G):
Code: Enable the Interior lighting (extended) MMI item:
[07 - Control Head]
[Adaptation - 10] -> Channel 1 add 2 to the existing value

MMI high (2G hidden menu as alternative)
If you choose to use the 2G hidden menu you will find the setting using the following:
DIAG SETTINGS -> APK 0x01, 0x0B, 0x0C -> Interior lighting (extended)

MMI 3G

This can only be activated through hidden menu

Enter hidden menu - choose car - choose carmenuoperation - select interior light - set to 5 to allow adjustment whist moving - press return - select cardevicelist - choose interior light and press to fill box in - press return

Reset MMI (press setup, scroll wheel and top right button next to scroll wheel at the same time)

Option will show in MMI

Enable interior lighting for facelift cars

[09 – Cent. Elect.]
[Coding - 07] -> [Long Coding Helper] -> Byte 16
Bit 6 - Interior/Ambience Lighting Adaptation active
Hidden menu - [carbusassignment] - Interior Light to [CAN Komfort 1/9]"
________________________________________

Enable fog lamp to come on for the same side as that turn signal

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Check the box or change :Bit 0 set to 1
________________________________________

Enable Front Turn Signals as Parking lights

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
Once the change has been made you can enable the front turn signals as DRL's by making the following change:
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 6 - Check the box or change :Bit 0 set to 1
________________________________________

Enable Gauge Test/Needle Sweep

[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________

Enable Headlights on all the time

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 5 - Check the box or change (Bit 5 Set to 1)
________________________________________

Enable Import CDs to MMI's HD

[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"
________________________________________

Enable Independent Fogs control with high beams

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 – (Rear) Uncheck the box or change :Bit 2 to 0
________________________________________

Enable Lap Timer

[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 - Check the box for "Lap Timer active"
______________________________________

Enable Remote Operation Windows and Sunroof

[46 - Cent. Conv.] [Coding - 07] -> [Long Coding Helper] Byte 2
Bit 2 - Set to 1
______________________________________

Enable Rear Tail Lights on with DRLs

[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 7 - DRL's via Tail Lets Active (1 = Active)
________________________________________

Enable Release Parking Brake without putting foot on Brake

[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 Set to 0
________________________________________

Enable Release Parking Brake without putting seatbelt

[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 Set to 0
________________________________________

Enable Reverse mirror tilt

[52 Door Elect, Pass.] -> [Coding - 07] -> [Long Coding Helper] -> Byte 4
Bit 3 and Bit 2 set to 1
________________________________________

Enable Speed through MMI

[56 - Radio] [Adaptation - 10] -> Channel 02, Set to 1
Does not work if NAV equiped
________________________________________

Enable ‘Tourist’ Mode – Headlight Convertor (MMI 2G)

[09-Central Elect]
[Coding – 07]
[Long Coding Helper] - Byte 4, Bit 6 = 1
Enables the 'connection' between Cent. Elect and the Headlight Convertor MMI menu item
[55-Xenon Range]
[Adaptation – 10]
[Channel 10] - 0 = Disable 1 = Enable
Press ‘Test’ and then ‘Save’
Enables the Headlight Convertor MMI item under the CAR button.
Restart MMI to see changes.

________________________________________

Enable TPMS
* only works with certain ABS modules - see below link *

http://www.audienthusiasts.com/VagComABS.html
________________________________________

Enable Video in motion on MMI

[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI
________________________________________

Set Audi parking system - Switch OFF Speed

[10 - Park/Steer Assist] [Adaptation - 10] -> Channel 23
Set to 20 (max value in km/h)
________________________________________

Set ADS to specific preset Comfort, Auto, Dynamic or Individual

[09 – Cent. Elect.][Security Access - 16]
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value.

________________________________________

Set Headlight washer - Duration

[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________

Set Headlight washer - Cycles

[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 26
change to e.g. 10
________________________________________

Adjust Consumption in DIS

[17 - Instruments]
[Adaptation - 10] -> Channel 3
change 100 to xxx (see samples below)

Sample 1 - Calculation based on volume per distance (e.g. l/100km):
DIS: 9,3 l/100 km.
Real: 9,8 l/100 km. (100 * 9,8 / 9,3 = 105,38)
Channel 3 will be changed from 100 to 105

Sample 2 - Calculation based on distance per volume (e.g. MPG):
DIS: 23 MPG.
Real: 24 MPG. (100 * 23 / 24 = 95,83)
Channel 3 will be changed from 100 to 96
________________________________________

Adjust LED brightness

[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 03
Set between 5 and 100 (5 being lowest and 100 brightest)
________________________________________

Select language in DIS:

17 - Instruments
Byte 8 -> Bit 0-4 - ->
Select the language.
________________________________________

Activate SDS for cabriolet:

5F–Information Electr.
Change Byte 15 – Bit 0 to 1
Change Byte 16 – Bit 0 to 0
________________________________________

Change fuel-tank charisterics:

17 - Instruments
Adaption - change channels 30 and 33
________________________________________

To increase radio play time after car is turned off:

In the Hidden Menu:

MMI 2G:
"MMI->SETTINGS->Standby Timer" - will allow you to hear e.g. Radio or CD longer before MMI shutdown (if ignition is OFF) - default 10 min. and the max. is 60 min.

MMI 3G:
From the main screen select 'onofftimer', set 'Standby delay'. The maximum value is 30 minutes.

 

[ruairi83]

Great find!

 

[Archies]

Brilliant that is,

Cheers

Archie...

 

[Kjaer85]

Somebody make this a sticky!!! I'm gonna sit in the car with my laptop the next couple of days

 

[Big-Boy]

Not bad, but it's all copy-paste:
AudiEnthusiasts Vag Com
VCDS
VCDS & Hidden menu: The complete list

And the best, By Categories Car
stemei.de .VCDS Codierungen .Codierungsservice .Webdesign - Stefan Meier - Codierungen - VCDS Codierungen, Webdesign
On the German but Chrome with translator

 

[Big-Boy]

Not bad, but it's all copy-paste:
AudiEnthusiasts Vag Com
VCDS
VCDS & Hidden menu: The complete list

And the best, By Categories Car
stemei.de .VCDS Codierungen .Codierungsservice .Webdesign - Stefan Meier - Codierungen - VCDS Codierungen, Webdesign
On the German but Chrome with translator

Thanks

 

[Big-Boy]

Not bad, but this is all copy-paste from other websites or forums

There are places where this is much better explained

 

[Anthony566]

Not bad, but this is all copy-paste from other websites or forums

There are places where this is much better explained

And your point is re the copy and past ??? I don't think anyone is claiming ownership of this the question was do we have a list like this one ??

 

[Big-Boy]

And your point is re the copy and past ??? I don't think anyone is claiming ownership of this the question was do we have a list like this one ??

Here's a better list
VCDS
This is the best - with a list of all cars
stemei.de .VCDS Codierungen .Codierungsservice .Webdesign - Stefan Meier - Codierungen - VCDS Codierungen, Webdesign
On German language but Chrome with translator

Good luck


PS: This does not work on all models

Enable Optical rear parking for cars without front parking sensors

[10 - Park/Steer Assist] [16 - Security Access - 71679] do it [07 - Coding] Byte 0 - Bit 4 change 0 to 1


The control units with graphical display support are :
8K0919475A
8K0919475C
8K0919475E
8K0919475G
8K0919475P (acording to etka, only for Q5 and A5 Sportback)
8K0919475J
8K0919475R
The PR code for parking front and rear is 7X4,7X8

Non graphic support (only back parking sensors):
8K0919475
8K0919475B
8K0919475D
8K0919475F
8K0919475S (acording to etka, only for Q5 and A5 Sportback)
8K0919475H
8K0919475Q

 

[Big-Boy]

Hi do we have a VCDS Mod list like this one ?


Enable Video in motion on MMI

[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI

With this nothing you can. Where is the explanation for Instructions 2G or Instructions 3G:
I miss a lot of explanation and this:
Manually Decoding Your Security Code or Automatic VIM Generator

When you copy an instructions - copy a complete instructions not just one part