Dis and cruise help!!!

[Jamie1087]

Hi all, I have installed cruise and dis, had them coded , car accepted codes but for some reason they are not working.
Any help will be much appreciated, will post up the vag code errors when I get them sent to me

 

[Darren92]

Ok so you're missing some information here. What is the part number of your SWCM?

 

[NHN]

+1

 

[Jamie1087]

I didn't do the coding (and have no idea how to) so what info is required? And as for part number I don't know the number, I bought the parts off a breaker and it said it was off an A4 b7 avant

 

[NHN]

Get someone on it that knows what they're doing, no offense.

Whereabouts are you located?

 

[Jamie1087]

I'm located at n swansea

 

[NHN]

Ok not close to be lol, I have a job next week in Bromsgrove if you can get to there Friday/weekend.

 

[Jamie1087]

Ok not close to be lol, I have a job next week in Bromsgrove if you can get to there Friday/weekend.

Can't get there sorry

 

[SemedoB6]

If the car accepted the coding it's because the module is correct..
Beyyer look at clutch switch because if this is faulty cruise control won't work either..

Sent from my SM-G935F using Tapatalk

 

[Jamie1087]

Looking back at my receipts, the stalks I bought are off an a6 not an A4

 

[SemedoB6]

Depending on the part number it should work..
A4 and a6 share a few parts..

Sent from my SM-G935F using Tapatalk

 

[Darren92]

If the car accepted the coding it's because the module is correct..

Not always the case.

 

[SemedoB6]

My module only accepted the code when I got the new one.
I tried the cc code on module that wouldn't support it and car simply didn't take it..

Sent from my SM-G935F using Tapatalk

 

[Jamie1087]

These are the error codes,

Saturday,26,August,2017,14:34:54:55632
VCDS Version: Release 17.8.0 (x64) Running on Windows 10 x64
www.Ross-Tech.com
LR Enginering
Address 01: Engine Labels: 03G-906-016-BLB.clb
Control Module Part Number: 03G 906 016 JD HW: 028 101 265 4
Component and/or Version: R4 2,0L EDC G000SG 9643
Software Coding: 0000072
Work Shop Code: WSC 66565 257 00032
VCID: 6ED32F88794E553668-803A
2 Faults Found:

005785 - Powertrain Data Bus
P1699 - 000 - Missing Message from Steering Wheel Electronics
Freeze Frame:
Fault Status: 01100000
Fault Priority: 3
Fault Frequency: 4
Reset counter: 255
Mileage: 178147 km
Time Indication: 0

Freeze Frame:
RPM: 0 /min
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 12.16 V
Bin. Bits: 00001100
Bin. Bits: 00000000
(no units): 0.0

001384 - Cruise Control Switch (E45)
P0568 - 000 - Implausible Signal
Freeze Frame:
Fault Status: 01100000
Fault Priority: 3
Fault Frequency: 1
Reset counter: 255
Mileage: 178147 km
Time Indication: 0

Freeze Frame:
RPM: 0 /min
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 12.24 V
Bin. Bits: 11001100
Bin. Bits: 00000000
(no units): 0.0

 

[Jamie1087]

All sorted not, massive thanks to tezgreig!! He sorted everything out

 

[Wayne p]

All sorted not, massive thanks to tezgreig!! He sorted everything out

How did you sort this ? I've just fitted dis stalk and activated it ,, instantly low screen wash illuminated but buttons on stalk do nothing!! Thanks

 

[Jamie1087]

How did you sort this ? I've just fitted dis stalk and activated it ,, instantly low screen wash illuminated but buttons on stalk do nothing!! Thanks

You have to take off the clocks, and splice into pin 1 from the blue plug out of the back and ground it ( it should be the brown and red wire. The washer bottle function won't work then but ist tricks the computer in to thinking the sensor is active, but it's not. If the pin is not the ( as on some models it's not,) you need to but the wiring kit then ground it

 

[Wayne p]

You have to take off the clocks, and splice into pin 1 from the blue plug out of the back and ground it ( it should be the brown and red wire. The washer bottle function won't work then but ist tricks the computer in to thinking the sensor is active, but it's not. If the pin is not the ( as on some models it's not,) you need to but the wiring kit then ground it

So once it's been grounded the functions on the stalk will work ? Thanks

 

[Jamie1087]

I believe it will work , if not try re coding it

 

[Wayne p]

Do I do pin 1 in the green plug or blue ?? Very hard to identify which is pin 1 also ? Thanks

 

[SemedoB6]

Do I do pin 1 in the green plug or blue ?? Very hard to identify which is pin 1 also ? Thanks

Blue plug.. If I remember correctly on the left side.
Very easy to identify. Remove the multi conector from the blue sleeve and you'll see it clearly numbered..
Can't get it wrong really..

Sent from my SM-G935F using Tapatalk

 

[Wayne p]

Blue plug.. If I remember correctly on the left side.
Very easy to identify. Remove the multi conector from the blue sleeve and you'll see it clearly numbered..
Can't get it wrong really..

Sent from my SM-G935F using Tapatalk

I've sorted it thank you ,, now have fully functioning dis stalk and mfsw ..

 

[SemedoB6]

I've sorted it thank you ,, now have fully functioning dis stalk and mfsw ..

Cheers. I'm glad I could help..
Good to know it's working now.

Sent from my SM-G935F using Tapatalk

 

[Jamie1087]

Glad to hear it!!