Auto switch to reverse camera

[saffauk]

Good day all

I recently retrofitted a OEM RVC and everything is working correctly except for having to select the camera every time I put it in reverse. By default it goes to the Park Assist screen.

Is there a way to change the default screen to the camera. It is a 2015 Avant.

 

[Chrisk1993]

The coding is wrong - should show the camera with the parking aid in the bottom corner.
Have you got vcds?

Sent from my SM-G900F using Tapatalk

 

[saffauk]

Hi yes coding as follows

Address 09: Cent. Elect. (J519) Labels: 8K0-907-063.clb
Part No SW: 8K0 907 063 DG HW: 8K0 907 063 DG
Component: BCM1 1.0 H16 0103
Revision: 07016001 Serial number: 00001106047301
Coding: 260000118034AFE01481700000001D0D4F9D070827090201000008004400030100000034000000

Address 5F: Information Electr. (J794) Labels: 4E0-035-6xx-5F.clb
Part No SW: 8R2 035 670 K HW: 8R2 035 670 J
Component: H-BNT-EU H50 0941
Revision: -------- Serial number: 517GZ0F7504206
Coding: 0F0101010006E3EF05809B5E00000403040000000000000000

Address 6C: Back-up Cam. Labels: 4L0-910-441.clb
Part No SW: 8T0 907 441 C HW: 4L0 907 441 B
Component: J772__Rearview 0040
Revision: --H04--- Serial number: 525PA8-J07924A
Coding: 1031007

 

[johnny161171]

With VCDS go to Controller 09 Central Electrics, then Long Coding, Long Coding Helper.
Select Byte 35 and tick bit 4. If bit 4 is not available as it was on mine, select "LCode2" on the top menu which should allow you to select Bit 4. This will change the HEX value to 34. Once Coded you need to go into the Parking Sensor Menu on the MMi, then disable Display and then re-enable the display (This is very important!)
The Reverse Camera will now be the default when reverse is selected and the OPC display will show on the right side over the camera image.

Make sure 6C is ticked in CAN gateway Installation list.
Make sure 5F is coded for byte 7, bit 1. Reboot MMI. Make sure 6C is coded correctly.

 

[saffauk]

Thanks you so so much Johnny161171.
All working as it should. Now my hair can grow back.

 

[banchory]

Good day all

I recently retrofitted a OEM RVC and everything is working correctly except for having to select the camera every time I put it in reverse. By default it goes to the Park Assist screen.

Is there a way to change the default screen to the camera. It is a 2015 Avant.

Hi Mate,
Want to do same where did you get the parts, and where did yo get them.
Thanks.

 

[banchory]

Hi Mate,
Want to do same where did you get the parts, and where did yo get them.
Thanks.

Sorry what parts did you need, it should of read.

 

[Chrisk1993]

Parts required depends on what mmi you have.

Sent from my SM-G900F using Tapatalk

 

[saffauk]

If you have a MMI 3G+ with nav you need the following.

Camera 5N0 827 566 AA
Controller 8T0907441C
Module Bracket 8K0907392A
Kufatec Loom Kit(it was too short as it was made for EU cars, extended and was ok)

You can follow the instructions that come with the kufatec and search other people as i did not take any pictures. only tricky bit was the power and the can bus wiring, rest is simple but be prepared to remove ALOT of plastic panelling carefully or the will break, I tried to follow the OEM route.

As for MMI 2G, i have no idea but there is a loom for that too.

Good Luck

 

[banchory]

If you have a MMI 3G+ with nav you need the following.

Camera 5N0 827 566 AA
Controller 8T0907441C
Module Bracket 8K0907392A
Kufatec Loom Kit(it was too short as it was made for EU cars, extended and was ok)

You can follow the instructions that come with the kufatec and search other people as i did not take any pictures. only tricky bit was the power and the can bus wiring, rest is simple but be prepared to remove ALOT of plastic panelling carefully or the will break, I tried to follow the OEM route.

As for MMI 2G, i have no idea but there is a loom for that too.

Good Luck

Thanks it is mmi3g did you get all the parts from Kufatec?
Thanks again mate

 

[saffauk]

I got most of it off of fleabay but also got quotes from audi. Just beware. There are some people claiming to sell a kit with new parts and its not.
I got caught and the clips were broken off of the camera and clearly 2nd hand. Luckily I had buyers protection and sent it back for a full refund.

Camera
ebay - 120
audi - 240

Controller
ebay - 180
audi - 310

Module Bracket
audi - 10

Kufatec Loom (there is another loom some people sell, the only things I didnt like about the kufatec was that all the wires were the same colour and not like the OEM wire colours and it was to sort)
Kufatech - 62

Thanks

 

[banchory]

I got most of it off of fleabay but also got quotes from audi. Just beware. There are some people claiming to sell a kit with new parts and its not.
I got caught and the clips were broken off of the camera and clearly 2nd hand. Luckily I had buyers protection and sent it back for a full refund.

Camera
ebay - 120
audi - 240

Controller
ebay - 180
audi - 310

Module Bracket
audi - 10

Kufatec Loom (there is another loom some people sell, the only things I didnt like about the kufatec was that all the wires were the same colour and not like the OEM wire colours and it was to sort)
Kufatech - 62

Thanks

Thanks very much Mate.

 

[mike60e]

Good day all

Nice car you have there..