Morning all, So I have carried out this retrofit in my A7. Installed the rear view camera, kufatek fakra cable from boot to camera module then to the MMI unit as per Kufatek instructions. I have VCDS so coded as per instructions also, but the camera is not working. It seems the issue according to VCDS is that 6C is not detected at all? Anyone have any suggestions why this might be? I connected as per the instructions on the rear of the MMI grey plug. Can high pin 6 Can low pin 12 These pins were already occupied on the connector so they have been spliced and connect to the existing wires that were in those pin locations is this correct? On the fakra connector in the rear of the car that plugs into the camera module I have the following voltages on these pins.. Pin 10 12v Pin 11 2.72v Pin 12 2.27v Does this look normal? Should I check anything else? If the CAN bus is not recognising the module then the module itself might be faulty? I guess there is no easy way to test this? Any help much appreciated or where to look if possible, carried out a search with not much info returned. Thanks Matt
So vcds autoscan doesn't show the camera module as not registered? Assuming you've coded other modules given 6C isn't detected? Scan would be useful.
Hello NHN, Thanks for your reply. Just auto scanned the car and something is definitely not right... See attached.. https://wetransfer.com/downloads/fe...88367a8a0db08c09d162e82a20201001142102/f9773f One is a auto scan I carried out end of August just after I got the car, the other is today. Now I am not sure why so many errors have occurred as the car has been not used at all since the two scans apart from a few trips. The only thing that has really changed is the installation of the camera, module and wires. I'm thinking perhaps the CAN H&L wires I've spliced to the rear of the MMI on the grey connector on pins 6 & 12 are causing all these issues? Coding as follows Address 19 Added 6C to list Address 5F Adaption menu display PDC Active Address 9 Byte 35 Bit 4 Set to 1 Then carried out MMI reset with the buttons on the consol. Thank you for any help you can offer.
01/10 scan shows that you cannot talk to the camera module, which could be: 1) faulty module 2) faulty CAN connection 3) faulty power 4) faulty earth need to bottom out this issue before you can progress. edit: your coding is incorrect also, not that it will matter until the module issue is resolved, but you need to activate VPS and set its bus also.
Hello DJ Alix, So had another look at the connections behind the MMI just to be sure and low and behold CAN hi & low were incorrect! This has now been rectified and I can now see the 6C module in VCDS. I must admit I followed the Kufatek instructions which are pretty good but I got a bit lost towards the end with the coding and adaptions required, thinking that i had carried out the required steps. So I have carried out another scan since the correction above and now getting the following.. https://wetransfer.com/downloads/28...7c9f873fdf3fd30c01b6d99f20201001204303/609524 Sorry to be a pain but would you be able to advise what needs to be coded further? I am more than happy to reimburse for time and advice with this as i know it is sacred info. Thanks in advance
Made some good progress today and I have got the RVC to work! As DJalix said the Adaptions had not been carried out on the VPS so that has now been done. In the CAN gateway I had two 6C's ticked and two 17's ticked so removed the tick on the first of the two and this rectified the faults I was getting. Also sorted out the steering colum with a basic setting adjustment so all good apart from the dreaded 6C module. So, i got to see the RVC in action on the display but without the guidelines which the optical parking assist showed, is this normal should they should up with the steering angle? After a few seconds the screen then goes blank and the feed is gone. Went back into 6C and found the following fault codes (when cleared, the RVC works again but only for a few seconds and the faults are logged again) Unfortunately at a standstill again with what to do next? I try to carry out the basic setting but I get the error "request is out of range" Here is the log... https://wetransfer.com/downloads/a4...8306251e543f9403bbeaac6f20201002160004/00b5cd
Time to go over all your installation steps and connections again to make sure that all has been completed correctly. if you were in London I would say pop over as you kinda need some experienced eyes on this now.
Thank you DJAlix, If I was closer I would pop over for sure! Ok.. So I have gone over everything as suggested and rechecked my steps to ensure I've not missed anything. 1. Wires installed from RVC in boot handle to control module to MMI. 2. 6C Module installed in boot & connected to 12v+ constant rail & earth point. 3. Fakra cable connected from camera to module then to rear of MMI Blue quad lock plug PIN 6 - Video Cable PIN 12 - Shielding 4. CAN wires connected correct to grey quad lock connector PIN 6 - CAN High PIN - 12 CAN Low 5. Coded Address 19 added 6C (2nd one on list) 6. Coded Address 9 byte 35 bit 4 set 1 7. Address 5F adaption Menu display PDC Active 8. Address 5F adaption VPS active 9. Address 5F adaption VPS msg bus terminal 15 10. Reset MMI via control buttons 11. 6C coded to Audi A7 with optical park assist & logo lines integrated. Basic setting is still required but I will get to that once the damn thing is working with no other errors. I know it is working as if i clear all DTC errors and activate the camera via the dash button or selecting the R gear, up pops the camera with guidelines! After a second or so, the guidelines disappear, then the camera display goes blank. I can repeat this if I clear the DTC again in 6C module. So, I am thinking this is a software issue somewhere and not hardware based on this evidence. Code: Sunday,04,October,2020,10:10:35:52653 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 20.4.2.0 (x64) Data version: 20200730 DS317.0 www.Ross-Tech.com VIN: WAUZZZ4G4GN116630 License Plate: CAM ADVID -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 6C: Back-up Cam. Control Module Part Number: 4S0 907 441 B Component and/or Version: D4-PA RVC Mid H07 0050 Software Coding: 027503014A01000100 Work Shop Code: WSC 02391 VCID: 326E8F667DE2CC16D5-8066 Advanced Identification/FAZIT Identification: PA8-001 Date: 01.07.15 Manufacturer number: 0004 Test stand number: 0569 Flash Status Programming Attempts(application): 0/0/0/0 Programming Attempts(data): 1 Successful Attempts(data): 1 Flash Date: 00.00.00 Flash Tool Code(data): 00200 785 02391 Misc. Hardware number: 5Q0 907 441 A Workshop System Name: J772 Equipment/PR Code: 000000000000000000000009 Dataset Number: 4S0909460A Dataset Version: 0008 ASAM Dataset: EV_CamSysRearPANAAU914 ASAM Dataset Revision: 002002 VCDS Info: VCID: 326E8F667DE2CC16D5-8066 Labels: 5Q0-907-441.clb ROD: EV_CamSysRearPANAAU914.rod -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 6C: Back-up Cam. Labels: 5Q0-907-441.clb Control Module Part Number: 4S0 907 441 B HW: 5Q0 907 441 A Component and/or Version: D4-PA RVC Mid H07 0050 Software Coding: 027503014A01000100 Work Shop Code: WSC 02391 785 00200 ASAM Dataset: EV_CamSysRearPANAAU914 002002 (AU57) ROD: EV_CamSysRearPANAAU914.rod VCID: 326E8F667DE2CC16D5-8066 4 Faults Found: 10489856 - No Basic Setting B2010 00 [009] - - [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13705512 - Databus U1121 00 [009] - Missing Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13706023 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13706024 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Chassis Type: 4G-AU57 (4G8) Scan: 01 02 03 05 08 09 15 16 17 19 28 30 36 3B 42 44 46 52 53 55 5F 62 6C 6D 72 82 85 VIN: WAUZZZ4G4GN116630 Mileage: 70646km-43897miles 01-Engine -- Status: OK 0000 02-Auto Trans -- Status: OK 0000 03-ABS Brakes -- Status: OK 0000 04-Steering Angle -- Status: OK 0000 05-Acc/Start Auth. -- Status: OK 0000 08-Auto HVAC -- Status: OK 0000 09-Cent. Elect. -- Status: OK 0000 15-Airbags -- Status: OK 0000 16-Steering wheel -- Status: OK 0000 17-Instruments -- Status: OK 0000 19-CAN Gateway -- Status: OK 0000 28-HVAC, Rear -- Status: OK 0000 30-Special Function II -- Status: OK 0000 36-Seat Mem. Drvr -- Status: OK 0000 3B-Sensor Elect. -- Status: OK 0000 42-Door Elect, Driver -- Status: OK 0000 44-Steering Assist -- Status: OK 0000 46-Central Conv. -- Status: OK 0000 52-Door Elect, Pass. -- Status: OK 0000 53-Parking Brake -- Status: OK 0000 55-Headlight Range -- Status: OK 0000 5F-Information Electr. -- Status: OK 0000 62-Door, Rear Left -- Status: OK 0000 6C-Back-up Cam. -- Status: Malfunction 0010 6D-Trunk Elect. -- Status: OK 0000 72-Door, Rear Right -- Status: OK 0000 82-Heads Up Display -- Status: OK 0000 85-On Board Cam. -- Status: OK 0000 ------------------------------------------------------------------------------- Address 01: Engine (J623-CREC) Labels:. 06E-907-551-CGW.clb Part No SW: 4G2 907 551 B HW: 4H2 907 551 A Component: 3.0l V6 TFSI H10 0001 Revision: --H10--- Coding: 1A2500340527010B3800 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_ECM30TFS0214G2907551B 002001 ROD: EV_ECM30TFS0214G2907551B_002.rod VCID: 2A5E97064D3284D66D-807E No fault code found. Readiness: 1010 0001 ------------------------------------------------------------------------------- Address 02: Auto Trans (J217) Labels:| 0B5-927-156.clb Part No SW: 4G0 927 166 D HW: 0B5 927 156 K Component: 0B5 30TFSIRdW H03 0009 Revision: --H03--- Coding: 100001 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_TCMDL501021 001021 ROD: EV_TCMDL501021.rod VCID: 2E569B1671DAE8F6B1-807A No fault code found. ------------------------------------------------------------------------------- Address 03: ABS Brakes (J104) Labels:. 4G0-907-379-V2.clb Part No SW: 4G0 907 379 S HW: 4G0 907 379 S Component: ESP9 Premium H01 0530 Revision: -------- Serial number: -------------- Coding: 44A69E43226579C29B00 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_ESP9BOSCHAU57X 004018 ROD: EV_ESP9BOSCHAU57X.rod VCID: 418CD0AAD044678E5C-8014 No fault code found. ------------------------------------------------------------------------------- Address 05: Acc/Start Auth. (J393) Labels:. 8K0-907-064-05.clb Part No SW: 4H0 907 064 GP HW: 4H0 907 064 GP Component: BCM2 2.0 H37 0572 Revision: 00002001 Coding: 05BA6F4E000000000000 Shop #: WSC 02391 785 00200 VCID: 7DF46C5AE43CC36E78-8028 Subsystem 2 - Part No SW: 4H0 905 852 C HW: 4H0 905 852 C Component: J764 ELV MLB H40 0046 Serial number: 2315000204963002 No fault code found. ------------------------------------------------------------------------------- Address 08: Auto HVAC (J255) Labels:| 4G0-820-043-4Z.clb Part No SW: 4G0 820 043 CD HW: 4G0 820 043 CD Component: KLIMA 4 ZONEN H14 0112 Serial number: 13111500041083 Coding: 66A311783D0000 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_AirCondiComfoUDS 003008 ROD: EV_AirCondiComfoUDS_003.rod VCID: 63C03A226A98159E6E-8036 No fault code found. ------------------------------------------------------------------------------- Address 09: Cent. Elect. (J519) Labels:. 4H0-907-063-V2.clb Part No SW: 4H0 907 063 DH HW: 4H0 907 063 AH Component: BCM1 2.0 H20 0311 Revision: 15020001 Serial number: 00001213146801 Coding: 0105C01550349FE041014087800018000F9DC30A2F080201800008946100130200400034030000 Shop #: WSC 02391 785 00200 VCID: 71EC406AA864B70EEC-8024 Subsystem 1 - Part No SW: 4G2 955 119 HW: 4G8 955 119 A Labels: 1KX-955-119.CLB Component: WWS57X 150924 H38 0080 Serial number: 151002074517 Coding: 0045F7 Subsystem 2 - Part No SW: 8U0 955 559 C HW: 8U0 955 559 B Labels: 8U0-955-559.CLB Component: G397_RLFS H06 0004 Serial number: 60939576 Coding: 02006E Subsystem 3 - Part No SW: 4G0 941 531 BG HW: 4G0 941 531 BG Component: E1 - LDS H07 0044 Serial number: 10 11 2015 00000275 Subsystem 4 - Part No SW: 4H0 907 705 K HW: 4H0 907 705 C Component: EVLS-SG H08 0300 Serial number: WA121750000015675279 Coding: 020300 Subsystem 5 - Part No SW: 4H0 907 658 HW: 4H0 907 658 Component: AQ_Hum_Sensor H03 0003 Serial number: 2F998AD7000000000001 No fault code found. ------------------------------------------------------------------------------- Address 15: Airbags (J234) Labels:* 4H0-959-655.clb Part No SW: 4H0 959 655 H HW: 4H0 959 655 H Component: Airbag10.43 H82 0086 Revision: -------- Serial number: 003P1007C3PX Coding: 30333046313130313235554A305234473853 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_AirbaAU10BPAAU64X 001014 ROD: EV_AirbaAU10BPAAU64X_VW51.rod VCID: 3B70A242B2A80D5E06-806E Crash sensor for side airbag: driver side: Serial number: 3575HRB400Q551R0H9QN Crash sensor for side airbag: front passenger side: Serial number: 3585HRB400I551R08HG5 Crash sensor for side airbag: rear: driver side: Serial number: 3515JRB40513L83688KT Crash sensor for side airbag: rear: passenger side: Serial number: 3525JRB405V3JRS03OST Crash sensor for front airbag: driver side: Serial number: 3554VRB400U554Q2LI7- Crash sensor for front airbag: front passenger side: Serial number: 3564VRB400U554Q2H8T2 No fault code found. ------------------------------------------------------------------------------- Address 16: Steering wheel (J527) Labels:. 4H0-953-568.clb Part No SW: 4H0 953 568 H HW: 4H0 953 568 H Component: Lenks.Modul H04 0005 Revision: -------- Serial number: 90372OK7000K2 Coding: 000434 Shop #: WSC 02391 785 00200 VCID: 387ABD4E8B9E2646EB-806C Subsystem 1 - Part No SW: 4H0 951 528 E HW: 4H0 951 528 E Component: E221 - MFL H08 0010 Serial number: 24 10 2015 D0065939 No fault code found. ------------------------------------------------------------------------------- Address 17: Instruments (J285) Labels:| 4H0-920-xxx-17.clb-SRI1 Part No SW: 4G8 920 986 K HW: 4G8 920 986 K Component: TBenGb H11 0104 Revision: 07001088 Serial number: 658250915596036 Coding: 33A600020B432600010100 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_RBD4K 004055 ROD: EV_RBD4K_AU57.rod VCID: 408AD5AEDB4E6E8653-8014 No fault code found. ------------------------------------------------------------------------------- Address 19: CAN Gateway (J533) Labels:* None Part No SW: 4G8 907 468 F HW: 4G8 907 468 Component: J533--Gateway H14 0083 Revision: -------- Serial number: 00000002055273 Coding: C0CD073018 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_GatewPkoUDS 001028 ROD: EV_GatewPkoUDS_001_AU57.rod VCID: 3B70A242B2A80D5E06-806E Battery Monitoring Control Module: Subsystem 1 - Part No SW: 8T0 915 181 HW: 8T0 915 181 Component: J367-BDMHella H03 8041 Serial number: 9732888303 Voltage stabilizer: Subsystem 2 - Part No SW: 8K0 959 663 F HW: 8K0 959 663 F Component: J532_DCDCStab H23 0022 Serial number: 150905000000000000F1 No fault code found. ------------------------------------------------------------------------------- Address 28: HVAC, Rear (E265) Labels:* 4G0-919-158.clb Part No SW: 4G0 919 158 Q HW: 4G0 919 158 Q Component: KLIMA FOND H08 0112 Serial number: 12111500041074 Coding: 22 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_ClimaContrUnitRearUDS 003004 ROD: EV_ClimaContrUnitRearUDS_003.rod VCID: 3D74AC5AACBC036E38-8068 No fault code found. ------------------------------------------------------------------------------- Address 30: Special Function II (J843) Labels: 8K0-907-440.clb Part No SW: 4H0 907 440 HW: 4H0 907 440 Component: STS H06 0030 Revision: S0H06000 Serial number: 00000000082277 Coding: 01010101000000000001000102 Shop #: WSC 02391 785 00200 VCID: 64C2393E679612A697-8030 No fault code found. ------------------------------------------------------------------------------- Address 36: Seat Mem. Drvr (J136) Labels: None Part No SW: 4G8 959 760 HW: 4G8 959 760 Component: MEM-FS H03 0157 Revision: AA000000 Serial number: 00000171842404 Coding: 00781B0000006001000001010101102030303232203232 Shop #: WSC 02391 785 00200 VCID: 77F87E72C600E93E22-8022 No fault code found. ------------------------------------------------------------------------------- Address 3B: Sensor Elect. (J849) Labels: 4G0-907-637.clb Part No SW: 4G0 907 637 K HW: 4G0 907 637 F Component: SARA 6D H04 0056 Revision: -------- Serial number: EJ1BPA820AJRCT Shop #: WSC 00000 000 00000 ASAM Dataset: EV_SARA2 005012 ROD: EV_SARA2.rod VCID: 3666B376898AD036F9-8062 No fault code found. ------------------------------------------------------------------------------- Address 42: Door Elect, Driver (J386) Labels:. 4H0-959-793.clb Part No SW: 4G8 959 793 J HW: 4G8 959 793 G Component: TSG FA H03 0511 Revision: -------- Serial number: -------------- Coding: 011C56034E21620002080402 Shop #: WSC 02391 785 00200 VCID: 4798CEB2F66059BE92-8012 No fault code found. ------------------------------------------------------------------------------- Address 44: Steering Assist (J500) Labels:| 4G0-909-144.clb Part No SW: 4G0 909 144 T HW: 4G0 909 144 Q Component: RCevo H53 0202 Revision: 00000002 Serial number: 0000353552 Coding: 101000010001 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_RCEPS 106007 ROD: EV_RCEPS_106.rod VCID: 3A7EA746BD9234561D-806E No fault code found. ------------------------------------------------------------------------------- Address 46: Central Conv. (J393) Labels:. 4H0-907-064-46.clb Part No SW: 4H0 907 064 GP HW: 4H0 907 064 GP Component: BCM2 2.0 H37 0572 Revision: 00002001 Serial number: 0385834689 Coding: 013B0E22A0B9B805C3300A0400030D470000000000000000000000000000 Shop #: WSC 02391 785 00200 VCID: 7DF46C5AE43CC36E78-8028 Subsystem 1 - Part No: 4G0 951 177 A Component: Sensor, DWA 005 0002 Subsystem 2 - Part No: 1K0 951 605 C Component: LIN BACKUP HO H05 1501 Subsystem 3 - Part No SW: 4G8 959 591 A HW: 8V3 959 591 A Component: J245 PS40.402 H03 0004 Serial number: 0000FST000NHLG500000 Coding: 901E02 Subsystem 4 - Part No SW: 4G8 959 252 A HW: 4G8 959 252 Component: HSP-SG H11 0031 Serial number: WA122232000016854829 Subsystem 5 - Part No SW: 3AA 962 243 D HW: 3AA 962 243 D Component: GEB.F.Heckoef H16 0811 Serial number: 93658547 No fault code found. ------------------------------------------------------------------------------- Address 52: Door Elect, Pass. (J387) Labels:. 4H0-959-792.clb Part No SW: 4G8 959 792 J HW: 4G8 959 792 G Component: TSG BF H03 0511 Revision: -------- Serial number: -------------- Coding: 011C56034E21620002080402 Shop #: WSC 02391 785 00200 VCID: 4686C3B6F16A40B669-8012 No fault code found. ------------------------------------------------------------------------------- Address 53: Parking Brake (----) Labels: 4H0-907-801.clb Part No SW: 4H0 907 801 L HW: 4H0 907 801 A Component: EPB-4 H05 0017 Revision: -------- Serial number: 00000002163345 ASAM Dataset: EV_ParkiBrake 001029 ROD: EV_ParkiBrake_VW51.rod VCID: 316C806A60E4F70EAC-8064 No fault code found. ------------------------------------------------------------------------------- Address 55: Headlight Range (J745) Labels:| 4H4-907-357-V2.clb Part No SW: 4H4 907 357 E HW: 7P6 907 357 B Component: MxB-ECU 001 0100 Revision: -------- Serial number: -------------- Coding: 05FE02202A130200 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_HeadlRegulAUDIMXBAU64X 005009 ROD: EV_HeadlRegulAUDIMXBAU64X_005_AU57.rod VCID: 3462897E9FF6C226C7-8060 Led Headlamp Powermodule Left: Subsystem 1 - Part No SW: 7PP 941 472 K HW: 7PP 941 472 K Labels: 3D0-941-329.CLB Component: LED LeiMo li. H07 7570 Coding: E02100 Led Headlamp Powermodule Right: Subsystem 2 - Part No SW: 7PP 941 472 K HW: 7PP 941 472 K Labels: 3D0-941-329.CLB Component: LED LeiMo re. H07 7570 Coding: E02100 Matrix Headlamp Powermodule 1 Left: Subsystem 3 - Part No SW: 4H0 941 329 A HW: 4H0 941 329 A Labels: 3D0-941-329.CLB Component: MxB LeiMo li. H03 0031 Coding: E02100 Matrix Headlamp Powermodule 1 Right: Subsystem 4 - Part No SW: 4H0 941 329 A HW: 4H0 941 329 A Labels: 3D0-941-329.CLB Component: MxB LeiMo re. H03 0031 Coding: E02100 No fault code found. ------------------------------------------------------------------------------- Address 5F: Information Electr. (J794) Labels:* 4G1-035-MIB-HGH2.clb Part No SW: 4G1 035 018 HW: 4G1 035 021 D Component: MU-H-LND-EU 051 0389 Serial number: A733K0FB002289 Coding: 017503010000000013111102000A00132F000CE7F1700100DF Shop #: WSC 02391 785 00200 ASAM Dataset: EV_MUHig6C3Gen2HBAS 001115 ROD: EV_MUHig6C3Gen2HBAS_AU57.rod VCID: 5DB40CDA4CFC236E58-8008 Data medium: Subsystem 1 - Part No SW: V03 959 802 DD HW: ----------- Component: ECE 2018/2019 --- 0169 Serial number: -------------------- Display unit 1 for multimedia system: Subsystem 2 - Part No SW: 4G1 919 605 B HW: 4G1 919 605 B Component: DU8 C7 SV H63 0007 Serial number: AUZ8Z9FY803E73 Multimedia Operating Unit: Subsystem 3 - Part No SW: 4G2 919 610 F HW: 4G2 919 610 F Component: E380 BDT C7 H20 0250 Serial number: 90349OKG0000W Compact Disc Database: Subsystem 4 - Part No SW: V03 959 800 EG HW: ----------- Component: Gracenote2 --- 1012 Serial number: -------------------- No fault code found. ------------------------------------------------------------------------------- Address 62: Door, Rear Left (J388) Labels:. 4H0-959-795.clb Part No SW: 4G8 959 795 J HW: 4G8 959 795 G Component: TSG HL H03 0511 Revision: -------- Serial number: -------------- Coding: 010814024021620002080002 Shop #: WSC 02391 785 00200 VCID: 499CC88AE074AFCE84-801C No fault code found. ------------------------------------------------------------------------------- Address 6C: Back-up Cam. (J772) Labels:| 5Q0-907-441.clb Part No SW: 4S0 907 441 B HW: 5Q0 907 441 A Component: D4-PA RVC Mid H07 0050 Coding: 027503014A01000100 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_CamSysRearPANAAU914 002002 ROD: EV_CamSysRearPANAAU914.rod VCID: 326E8F6665E2CC16D5-8066 4 Faults Found: 10489856 - No Basic Setting B2010 00 [009] - - [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13705512 - Databus U1121 00 [009] - Missing Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13706023 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive 13706024 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 215 Mileage: 70646 km Date: 2020.10.04 Time: 10:09:48 passive ------------------------------------------------------------------------------- Address 6D: Trunk Elect. (----) Labels:* Redir Fail! Part No SW: 4G8 959 107 S HW: 4G8 959 107 H Component: HDSG-Modul H14 0049 Revision: 11014001 Serial number: 308500974 Coding: 0A3305C022 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_HDSGAu573 001022 ROD: EV_HDSGAu571.rod VCID: 4584C4BAC46C4BAE60-8010 No fault code found. ------------------------------------------------------------------------------- Address 72: Door, Rear Right (J389) Labels:. 4H0-959-795.clb Part No SW: 4G8 959 795 J HW: 4G8 959 795 G Component: TSG HR H03 0511 Revision: -------- Serial number: -------------- Coding: 010814024021620002080002 Shop #: WSC 02391 785 00200 VCID: 499CC88AE074AFCE84-801C No fault code found. ------------------------------------------------------------------------------- Address 82: Heads Up Display (J898) Labels:* None Part No SW: 4G8 919 604 N HW: 4G8 919 604 N Component: HeadUpDisplay H07 0306 Revision: 00000000 Serial number: 00000000000000 Coding: A20000 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_HUDContiC7 001027 ROD: EV_HUDContiC7.rod VCID: 3E76AB56A1BA187621-806A No fault code found. ------------------------------------------------------------------------------- Address 85: On Board Cam. (J852) Labels:| 7P6-907-217.clb Part No SW: 4H0 907 217 F HW: 4H0 907 217 A Component: DPC-SG H27 0081 Revision: -------- Serial number: 262130025421000 Coding: 60140000 Shop #: WSC 02391 785 00200 ASAM Dataset: EV_OnBoardCamerDPC 001007 ROD: EV_OnBoardCamerDPC.rod VCID: 2C52911E47C69AE69F-8078 No fault code found. End-------------------------(Elapsed Time: 05:37)-------------------------- Then this is the DTC after the camera is activated/goes blank Code: Sunday,04,October,2020,10:41:23:52653 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 20.4.2.0 (x64) Data version: 20200730 DS317.0 www.Ross-Tech.com VIN: WAUZZZ4G4GN116630 License Plate: -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 6C: Back-up Cam. Labels: 5Q0-907-441.clb Control Module Part Number: 4S0 907 441 B HW: 5Q0 907 441 A Component and/or Version: D4-PA RVC Mid H07 0050 Software Coding: 027503014A01000100 Work Shop Code: WSC 02391 785 00200 ASAM Dataset: EV_CamSysRearPANAAU914 002002 (AU57) ROD: EV_CamSysRearPANAAU914.rod VCID: 326E8F6665E2CC16D5-8066 5 Faults Found: 10489856 - No Basic Setting B2010 00 [009] - - [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 216 Mileage: 70646 km Date: 2020.10.04 Time: 10:37:12 passive 9683731 - External Trigger/Activation B13C3 13 [009] - Open Circuit Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 3 Fault Frequency: 1 Reset counter: 216 Mileage: 70646 km Date: 2020.10.04 Time: 10:39:14 active: waiting for return message 13705512 - Databus U1121 00 [009] - Missing Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 216 Mileage: 70646 km Date: 2020.10.04 Time: 10:37:12 passive 13706023 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 216 Mileage: 70646 km Date: 2020.10.04 Time: 10:37:12 passive 13706024 - Databus U1123 00 [009] - Received Error Message [New feature! Extended UDS fault detail is only supported by current gen. interfaces] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 216 Mileage: 70646 km Date: 2020.10.04 Time: 10:37:12 passive Thank you again for any help
Ok, just seen what the issue is. Did not spot it before as I have been viewing this thread via mobile and not a laptop. You have a newer vehicle (MY16 but was manufactured 27/11/2015) with an MIB2 Media unit and: 1) you are trying to retrofit a reversing camera, with external control module, for the older MMI vehicles. 2) while your chosen solution can be made to work you won't get guidance lines. What you are trying to retrofit is a reversing camera with an A6 control module (4S0 907 441B) which is not really compatible. If you wanted to go the external module route, for Video input etc, then you should use a 4G0 907 441B.... however as you have an MIB2 you should really be using an all-in-one camera handle unit 4G0 827 566A. As an aside, I can supply and fit the correct solution for you and also activate Audi Smartphone Interface given you have the correct MIB2 unit
Ahhh I did wonder, the more I looked into it the more I thought I had the wrong equipment for my year... But as I had the items present and it seemed it could be made to work (albeit with the correct module) I decided to procceed. Will remove the current module and see if i can recover some costs by fleabaying it and see if the correct unit is available. As I've carried out the wiring already are the two systems varying in connections much or will it be a rip out and start again affair perhaps? If only you were not so far away I would pop over and see you!. Thank you for identifying the issue here though DJAlix
Rip your installation out and source the correct camera for your vehicle together with its wiring in order to start over. There are small connection differences but wiring is different as what you have installed uses two looms when the correct camera only uses one. Not worth muddling through with what you have. Looking at your factory records you have a nice car there, do this retrofit correctly so you don't have any further issues
Agreed. Will source the correct equipment and start fresh. Since you have been so helpful DJAlix, do you sell the kit as a standalone? If so I would be happy to purchase from youself and tackle the fitting myself again. If you're interested in the old install I have, would be happy to send it your way if you can make use of it?
will price up a kit and pm you tomorrow with the details. Thanks for the offer but I don't use / supply used parts. As a genuine company I cannot warranty parts I don't know the history of.