With flappy paddles, but I think you can blank them.
http://www.ebay.co.uk/itm/Audi-A3-A4-A5-A6-A7-A8-S-line-Flat-Bottom-Steering-Wheel-NEW-8K0419091CPIXC-/331457486179?pt=LH_DefaultDomain_3&hash=item4d2c67dd63
Airbag...
Well checking the car while hot yesterday, the intake flap arm driven by the motor wiggles when you take the keys out of the ignition.
When the engine is running the arm pushes the flap in a similar fashion to how you would expect the main throttle butterfly to work i.e more throttle = more...
No, I'm probably going to get Rick @ Unicorn to have a go, as I now have the facility to squirt in the maps and the Bluefin figures seem a touch low compared to others.
Just getting christmas out the way first.
thanks for that.
it it active at anytime adjusting in relation to throttle angle.
is it used just during warm up.
i will check the rod but i have no error codes.
Just clocked 90K and the Throttle Body was quite clean.
A few squirts of carb cleaner and a wipe and it was as good as new.
Also took cam/rocker cover off and the cams and surrounding area were remarkably clean considering mileage. No wear on cams either.
Took the Throttle body/motor off today to give it a clean out and noticed another motor unit towards the rear of the intake manifold.
This has the P/N 06F 133 482 and appears to be called a 'Intake Manifold Flap'.
Can anybody explain what this does, when it operates and what the symptons are...
To perform an inspection of my camshafts do I just remove the top rocker cover or does the lower part also have to come off aswell, in order to give them a visual ???
Anyone know of a DIY guide ??
I need to inspect the cam lobes to help diagnose a minor misfire, as have now pretty muh...
Can anyone point me to a good outlet for RS4 split spoke replica alloys.
After some 18's or maybe 19's to replace my S-line 17's.
What width/offset should I go for and what's the recommended tyre size.
cheers
What does a Stage one run, would be good to see if any maps run much different.
My guess is 1.2bar ow end and 1bar top end.
What does the BlueFin run Vs' the others ?
Well changed the Thermostat on Friday, took about 1Hr 30Mins from start to topping the coolant back up.
A bit fiddly with those damn hose clips and the location of it, but the tip it to try not to take the hose clips off over the hose but go the otherway and just let them hang on the hard pipe...
Was looking at the HID's on my B7 and wondered if anyone in the world of Audi has de-tangoed and de-chromed.
I done the modification on my last Subaru, and thought could maybe do something similar on the Audi.
This is what was done on the Scooby, showing before and after :
Yeh torque pro, and it seems to pretty much match the car's gauge except then torque reads 82-85 the car gauge is about the thickness of the needle below 90.
Apparently normal operating temp is around 87 DegC which reads 90 on the car gauge.
Sounds like we may have the same issue as you can...
Just been out for another drive over lunch to see the effects of hot/cold running.
All the time I was logging coolant temperatures via OBD (Torque Pro).
Normal driving and it's sitting around 68-71 DegC and the missfire is quite easy to reproduce at light throttle 2000rpm. Easiest done on a...
I may be close, see my other thread : http://www.audi-sport.net/vb/audi-s4-a4-a4-cab-b7-chassis/172908-missfire-diagnosis-running-out-options-help.html
OK, from measurements I have taken the car's reading approx 11psi (0.75bar) peak dropping to 6psi (0.4bar).
The peak at 11psi comes in very early and soon tails off.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.