Search results for query: *

  • Users: kkk
  • Content: Threads
  • Order by date
  1. K

    Me7.5 adaptions

    Iv changed from a k03s hybrid at around 280 to 300bhp at 21psi to a g25 550 at around 14psi, will the me7.5 ecu adapt enough or does it have to he mapped again? Same maf and injectors Thanks
  2. K

    Headache with p0133 lambda slow response

    Hoping for some help as this is now doing my head in. I put a bbtk280 on my aum 1.8t in February and since then I have been chasing this code. First I changed the lambda twice, changed the fuel pump the fpr the coolent sensor, changed all my pipes put an airtec fmic to rule out the ebay job...
  3. K

    Gear linkage mount relocation

    Iv just fitted a k280 to my 1.8t 5 speed and realise I can’t bolt the linkage back to the gearbox. Has anyone else come across this, if so what can be done and will the cables need adjusting to get gears? This is all that’s stopping me driving thanks
  4. K

    Manifold recommendations

    Searching around all I can find is getting bill to port mine but can’t have my car off the road for a week. Iv ordered a k280 and Intake pipe but what manifold should I buy? Looking at the cast ones on eBay that say high flow, anyone got any experienc? I’m thinking cheaper than buying a new...
  5. K

    Best manifold for hybrid

    Searching around all I can find is getting bill to port mine. Iv ordered a k280 and I take pipe but what manifold should I buy? Looking at the cast ones on eBay that say high flow, anyone got any experienc? I’m thinking cheaper than buying a new standard then sending for porting. And would I...
  6. K

    abs fault

    My abs light is on and has a fault for the pump Could the pump cause an intrrmittant but there more than not vibrating throught the pedal wheel snd car? I need to replace the pump anyway but want to know if il need discs aswell. Thanks
  7. K

    17743 p1335 :(

    After getting near the end of sorting the faults on my car and always at the most inconvinient time, i.e pulling out a junction at half throttle, iv read so many posts with no fixed answer. Iv replaced cts and maf and they seem to read ok so could this only be down to an ecu fault? Would any...
  8. K

    why would my dash lights be so dim?

    Even with the dash dail turned right up they are dim, I fited a podi electrical gauge and even on the lowest setting for brightness its still brighter than my dash lights. Im sure its not right. Thanks Neil
  9. K

    ajq low boost

    Just fitted my boost gauge and only getting .4 bar but no codes and pulls ok, any ideas? Doesnt missfire and I thought all was ok till I see im only boosting half what its supposed to:/ Changed loads of bits aswell. Did find a mbc under the scuttle all disconected but may of been used by...
  10. K

    still need some help please

    i went out to get my tracking done and ran a log on the limited blocks i can on vcds whilst i was driving but it seems like im getting a low reading from the maf. but when i drove away from the garage in first at 4k it hit a brick wall and then kept missing/ hesitating at around 4k till i...
  11. K

    And lastly.... abs fault!!

    last fault that i know of with the car and as you all been so helpful theres no harm in asking. code is 01276. abs hydraulic pump (v64) signal outside spec. whats the procedure for checking it with basic vagcom 409.1? how can i determine whats at fault? so far i cleaned the fuses and put a...
  12. K

    Help with maf sensor pls

    need help before i waste any money, got fault code P0102 mass air flow sensor signal too low. i checked the pins with a multi meter and only got 4.9v on one of the pins but no 12v or any thing on any of the others. i then checked with vcds and its showing no reading on the maf block 003...
  13. K

    A3 quattro 5 spd clutch issue!

    i have a problom with my clutch and would like to know if anyone has come across this before and weather there is an easy fix for it? when the car is cold there is no pressure at all in the clutch pedel untill its below the pivot point but then has pressure and clucth works as it should, but is...
  14. K

    quick maf sensor question

    does any one know if i could change my air flow sensor to a differant part number. its currently fooc 2g2 040 but the other i have spare has 027 instead of 040. should it still work? thanks Neil
  15. K

    what happened to vagcom 409?

    iv just noticed its changed and cant use most of the features anymore like tba :/ if you still have 409 does it still work as it did?? where can i download a copy of 409??
  16. K

    my car problems, help needed!!

    Not had my A3 1.8T AJQ engine code for long and not had the chance to drive it properly yet. anyway, was out today and went round a round about on exit i put my foot down and it boosted then felt like it went flat and miss fired and i thought it was gonna die. so i limped home not knowing...