Search results for query: *

Hi All, I've got a few bits to sell: https://www.ebay.co.uk/usr/harbans11 Audi A3 2010 8p S-Line 2.0l tdi - SCUBA Blue Listed on ebay: - both rear doors - bonnet - undertray - rear boot lid - interior lights Not listed yet: - front bumper with aftermarket rs3 grille - rear bumper (dual...

Answering my own question, its: WVJ - Soul (Black)/Magma Red

Hi All, I'm looking to spray / refurb my leather seats. Does anyone know the paint code for the red for the red/black leather seats - these are electric/heated if that helps. Thanks in advance.

Soldered the wires together and placed into a single slot as per OEM - still blows the 10A fuse when sliding the seat back/forth or raising it up/down.

Hi All, So, I've managed to fit the electric / heated seats. The issue I am having is on the passenger side, when I slide the seat to either end the 10A fuse blows, the same happens on the drivers side where I raise or lower the seat and the fuse blows. What I noticed is, if I use a 15A fuse...

Manage to release the pin - for anyone else: insert a hair pin into the holes/gaps either side and then yank. It'll release the pin. I tried with a few other tools made specifically for this but no dice, surprisingly a hair pin worked. If you want the repair wire part no: 000979 406E

I ended up buying another 40 pin connector as imaged above. Any thoughts on how to unlock it to remove the pin? @NHN :)

So, the pin I need is T40/2 : Whats the part number for it?

If anyone needs the part number for one its: 1K0937524. Any thoughts on where I can obtain the connector that goes into the fusebox connector:

I think I found the part, but what pin goes on the other end? I either have it in slot SB29 (low) or SB53 (high) ...but unsure if its just a standard fuse slot pin?

Whats the repair wire that goes to the engine bay? It'll be this slot:

So, no luck fixing the heated seat. I've read the G345 is a small resistor that can be replaced but located inside the seat (with heating element) - do I remove the seat cover (looking for info on how this is done)

reseated the pins into the connector (D) and all fixed now, ran adaptation settings - still unable to up the temp on the drivers side. I'm thinking of replacing the G345 sensor but its located inside the seat?

Anyone have any thoughts on all the errors VCDS is showing?

any thoughts on the above: - I've tried changing the fuses - I've swapped the old hvac back over Unsure whats happened here.

I've also developed another issue: Saturday,06,January,2024,12:59:29:30584 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 23.11.0.0 (x64) HEX-V2 CB: 0.4643.4 Data version: 20231027 DS351.0 www.Ross-Tech.com Dealer/Shop Name: Ross-Tech LLC Workshop Code: 444...

So, I tried that - it still does the same. Could I wire up pin 1 and 13 (goes to fuse box) to confirm the seat does heat up?

Should the VCDS be driver side = driver side value passenger side = passenger side value?

so, I cabled it as per the 'right hand' version and when I look at the MVB I see the 'passenger' side is the driver side. But I read that VCDS use labels from the left hand version of the car?

Hey NHN, Thanks for the response. So, I've retrofitted the heated seats + HVAC unit. The issue I'm having is the driver side temperature reads 37 degrees (which is what position 6 is set to) before the seat even warms up. I'm guessing theres a bigger issue here. So, I wanted to amend the...