Search results for query: *

  1. O

    1.6TDI Fault Code P048A Exhaust Pressure Control Valve Stuck Closed - No Boost

    Same issue as @Maniek in the end, I had to get the valve & motor replaced.
  2. O

    1.6TDI Fault Code P048A Exhaust Pressure Control Valve Stuck Closed - No Boost

    My 1.6TDI threw an error today while driving, pulled up at a red light and the DIS showed a message that the auto start/stop system was disabled due to an error. Shortly after the glow plug light started flashing. The flashing glow plugs was accompanied by a complete loss of boost from the...
  3. O

    Enabling *** & subwoofer control without VCP - FL success

    This will work if you have or are looking to install the Audi Sound System. I'm not sure if this would enable the menu on the B&O system.
  4. O

    Enabling *** & subwoofer control without VCP - FL success

    To update your firmware you will need to download the correct version onto an SD card and use the developer menu on the MMI to run the update, there's plenty of tutorials on youtube for that if you need a guide. If you want to try editing the 0x03b address it would just be the subwoofer...
  5. O

    Enabling *** & subwoofer control without VCP - FL success

    Hi, yes if you used this method to enable the *** you will also need to amend channel specific settings in 0X003 (gain, delay, EQ). I used a parameter set from another 8V with *** and copied in the relevant parameters so the sound is as stock. I'd probably suggest trying to get hold of one for...
  6. O

    Enabling *** & subwoofer control without VCP - FL success

    Sorry I'm not sure if this would work for the B&O, the 0x30 dataset is only used on systems using the internal amp. The 0x3b dataset is still used with B&O so you may be able to add the subwoofer gain range through there but I don't know if this would actually work. Is your MMI on the latest...
  7. O

    Enabling *** & subwoofer control without VCP - FL success

    Ah would ah would expect you to notice it from the drivers seat then. I installed the wheel sub as it was a much easier retrofit, I never had the shelf sub so couldn’t say if there was a difference but imagine it’s better. Perhaps I’ll upgrade at some point
  8. O

    Enabling *** & subwoofer control without VCP - FL success

    Have you tried listening to it up close to make sure? I installed the spare wheel sub for the hatchback in to my saloon and it was hard to tell tbh, it was working though.
  9. O

    Enabling *** & subwoofer control without VCP - FL success

    I think you'd need VCP if not doing it this way, perhaps you can with ODIS if you can flash the right parameter sets.
  10. O

    Enabling *** & subwoofer control without VCP - FL success

    Hi, I’m not sure. From what I’ve read I think this way of activating the subwoofer control is only for the MIB2 as the 0x3B address doesn’t exist on the MIB1
  11. O

    Enabling *** & subwoofer control without VCP - FL success

    Go to settings -> info and there is a tick-box there. Just the standard OBD-II / EOBD under Audi is fine for this.
  12. O

    Enabling *** & subwoofer control without VCP - FL success

    What does the data look like before you import it? It should be the same as the hex code shown in the app. I copied the data out of the text box rather than exporting it (as circled in red before). I pasted that into an email, on the computer copied the code from the email into a .txt file...
  13. O

    Enabling *** & subwoofer control without VCP - FL success

    OK I just had a look, forgot the hex code copied out from Car Scanner already doesn't have whitespace in it! If you try and copy + paste the text directly into 010editor you'll notice the values change. You need to save the hex data into a new .txt file, then in 010 editor go to file -> import...
  14. O

    Enabling *** & subwoofer control without VCP - FL success

    I never had any issues with using the editor or templates, have you created the new file as a hex file and deleted all the whitespace characters?
  15. O

    Enabling *** & subwoofer control without VCP - FL success

    Hi Assume you are using the Car Scanner app, not the Carista one? Should be as below
  16. O

    Cambelt change and Audi All-In

    Hi, my 2017 1.6tdi is also due a cambelt and my 2 year approved used warranty just expired. My local dealer also quoted £720 for the 2 year service plan, and £920 for the belt. A local approved independent quoted £650 for the belt so I've booked in there instead. I'll keep an eye out on a...
  17. O

    Enabling *** & subwoofer control without VCP - FL success

    Yeah the various filters are all going to be applied at a Frequency and Quality, the Quality is effectively a measure of the bandwidth of the filter. You can approximate the bandwidth of the filter here - http://www.sengpielaudio.com/calculator-cutoffFrequencies.htm I've had a look at my...
  18. O

    Enabling *** & subwoofer control without VCP - FL success

    I was able to enable the subwoofer control on my *** setup by updating my MMI firmware to a newer version and editing 0x003B00 to add a range for the subwoofer control knob, depending on your current MIB2 High firmware this may work for you without having to update. I see what you are saying...
  19. O

    Enabling *** & subwoofer control without VCP - FL success

    Hi, if just adjusting the subwoofer gain do you not already have the control to adjust this on your MMI? (Thought that would be available on an S4!) My post above was for the MIB2 Std. For your MIB2 High you will want to check if the addresses and datasets are the same. I've quickly checked a...
  20. O

    Enabling *** & subwoofer control without VCP - FL success

    Hi all I thought I would share that I was able to enable the Audi Sound System and the subwoofer menu using just a bluetooth ELM327 dongle and the CarScanner mobile app. No VCP/ODIS/etc. required, though it did take quite a lot of research! Looking through the forum I didn't see anyone having...
Top
Back