Revo Stage 1+ dyno results

[xpoweruk]

Went to Riverside Racing today to get the S4 on the Dyno.
http://www.riverside-racing-uk.com/
They said to expect between 440/480 as that was the usual 1+ figures the get.

Di pretty well in the end

Car was run 3 times on each map,best run as shown
99ron Tesco momentum was the fuel i used.

 

[ianv5]

Good figures!

 

[razza1]

What's the mods? Seems too high tbh...

 

[xpoweruk]

What's the mods? Seems too high tbh...

I said the same,TBF the chap said he'd never seen one run over 480 with a stage 1+

But TBH the headline figure doesn't really matter to that extent,I dont spend that much time @7k lol.

I'm happy with the 6,500rpm figure as a headline figure (so 470-480)

Great pub numbers though

REVO Stage 1+ with REVO intake , Milltek ValveSonic

Oh & Millers Nanodrive oil http://www.millersoils.co.uk/nanodrive.asp

 

[GAS MONKEY]

Nice looks to be running spot on

 

[razza1]

Does that have the lightweight pulleys then?

 

[xpoweruk]

Does that have the lightweight pulleys then?

As in the charger pulley?

If so then yes,equivalent to a Stage 2 if you will

 

[ianv5]

I said the same,TBF the chap said he'd never seen one run over 480 with a stage 1+

But TBH the headline figure doesn't really matter to that extent,I dont spend that much time @7k lol.

I'm happy with the 6,500rpm figure as a headline figure (so 470-480)

Great pub numbers though

REVO Stage 1+ with REVO intake , Milltek ValveSonic

Oh & Millers Nanodrive oil http://www.millersoils.co.uk/nanodrive.asp

Run Millers nanodrive in my 2.0TFsi avant with Revo stage 1. Now cheaper since I had the oil consumption fix!

 

[razza1]

As in the charger pulley?

If so then yes,equivalent to a Stage 2 if you will

Ah ok, makes sense then given the exhaust, confused me with the 1+

 

[wolfie138]

hope you've got a good clutch :-D

 

[S4_V6T]

Went to Riverside Racing today to get the S4 on the Dyno.
http://www.riverside-racing-uk.com/
They said to expect between 440/480 as that was the usual 1+ figures the get.

Di pretty well in the end

Car was run 3 times on each map,best run as shown
99ron Tesco momentum was the fuel i used.



View attachment 73232 View attachment 73233

Those are some excellent figures and I am sure you are very happy with them.
Recently had my car on the dyno and it produced 475 bhp. That is with the APR Stage 2+, ECS Intake and Milltek Non Res exhaust.

How are you getting on with your clutch? Did you happen to ever find an uprated clutch fork? I think I may need another one... Again!
My clutch is holding up well and I have now covered roughly 7500 miles on the new set up now. Just wish I could say the same about the clutch fork.

 

[xpoweruk]

Those are some excellent figures and I am sure you are very happy with them.
Recently had my car on the dyno and it produced 475 bhp. That is with the APR Stage 2+, ECS Intake and Milltek Non Res exhaust.

How are you getting on with your clutch? Did you happen to ever find an uprated clutch fork? I think I may need another one... Again!
My clutch is holding up well and I have now covered roughly 7500 miles on the new set up now. Just wish I could say the same about the clutch fork.

I had to go back to the standard set up in the end as I needed the car back on the road.S currently running anew OE clutch.
In my case it was the uprated clutch pressure plate that failed