1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Who says Santa only comes once a year!? (warning engine p0rn content)

Discussion in 'A4/S4 forum(B5 Chassis)' started by jcb, May 29, 2008.

  1. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    Nice man from DHL arrived....

    [rolf harris voice]...."can you see what it is yet"
    [​IMG]

    .
    .
    .
    .
    .
    .
    .
    .

    [​IMG]
    behold the 2.0l 20v in the making....OK so not that exciting for you but I have been waiting for 6 months for this lot!!
    92.8mm forged crank, 83mm supertech pistons, Scat rods, supertech inconel exhaust/inlet valves,Titanium springs/retainers, 83mm multilayer metal gasket, raceware head and main bearing studs, eurospec bearing set.

    Block bored to 83mm and painted a tasteful silver
    [​IMG]

    GT2871 (soon to be added VBand exhaust housing)
    [​IMG]
    [​IMG]

    going to be running a tubular custom vband exhaust manifold, 3" DP, 2 3/4" Miltek, Forge FMIC, 630cc genesis injectors, 90mm Ford Lightning MAF and Tapp Auto Software, Tial 40mm V band Wastegate and an EBC.

    Looking for 200bhp at 4000rpm and somewhere north of 350bhp at 7000rpm.
    Dyno below compares a Gt2871 with a Gt3071.....on a 1.8....figures are on a 2wd....at the wheels
    [​IMG]

    all I need now if the spare time, energy and skill to put it together and not balls it up, whilst doing the brakes and fitting the S4 front back and sides!!
    looking forward to freeing up some space in my Audi parts store, I mean garage!
    #1
  2. docurley
    Offline

    docurley Moderator Staff Member Moderator

    Joined:
    Dec 12, 2003
    Messages:
    3,859
    Likes Received:
    25
    ooooooooooooooh very nice:hubbahubba:
    #2
  3. Biglockie
    Offline

    Biglockie Aye you know it makes sense

    Joined:
    Nov 27, 2006
    Messages:
    1,032
    Likes Received:
    0
    Very very very nice!!!!

    Ed can you send me the details on the rods and the head gasket, that what i need to complete my build, oh and the Bigg Ass Turbo!!!
    #3
  4. Lee Goodall
    Offline

    Lee Goodall ..got my head together!

    Joined:
    Oct 22, 2007
    Messages:
    2,231
    Likes Received:
    1
    Excellent.. wish Santa would spread it about a bit! LOL
    #4
  5. Andy.B
    Offline

    Andy.B Member

    Joined:
    Jul 16, 2007
    Messages:
    401
    Likes Received:
    0
    Mmmmmm i could only wish :salute:
    #5
  6. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    standard 2.0FSI 83mm head gasket
    happen to have a spare set of Scat rods that will be going on eBay this weekend if no-one wants them. they are standard I beam forged rods with 20mm wrist pin so you can;t use the stock 19mm pin from the OEM pistons. new pistons required.
    if you just want rods you need IntegratedEngineering drop in rods. give Bob a ring a Qedpower.com
    top bloke, has forgotten more than we will ever know about VAG engines.
    #6
  7. Soupie69uk
    Offline

    Soupie69uk Owner

    Joined:
    Mar 10, 2004
    Messages:
    2,787
    Likes Received:
    6
    OOOH lovely, hope I can have a spin in this once its done please.
    #7
  8. Broken Byzan
    Online

    Broken Byzan Photographic Moderator Staff Member Moderator

    Joined:
    Apr 26, 2004
    Messages:
    12,579
    Likes Received:
    270
    Anyone with an AEB or APU engine will be fine as they have 20mm pins,its the rest and most of the A3/TT ones that were 19mm
    #8
  9. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    you are correct,was only thinking of myself
    codes for those who need em (courtesy of Michael Ghia on ClubGTI)
    [​IMG]
    [​IMG]
    #9
  10. Biglockie
    Offline

    Biglockie Aye you know it makes sense

    Joined:
    Nov 27, 2006
    Messages:
    1,032
    Likes Received:
    0
    Ed might be interested in the rods dude, putting new pistons in anyways so it wont make any difference

    APU engine code, need a big port head!!! anyone know of one goin spare????
    #10
  11. Broken Byzan
    Online

    Broken Byzan Photographic Moderator Staff Member Moderator

    Joined:
    Apr 26, 2004
    Messages:
    12,579
    Likes Received:
    270
    Chris, unless you going for massive power the APU head "may " actually flow better,over on the 'zine its been disscussed that unless you are runnig around 450bhp upwards you wont flow enough to need the big port head (AEB) In fact you could actually lose torque by using it on too small a turbo setup.

    if i could be arsed i would swap my AEB for your APU anyday as i have an APU bottom end in anyway

    Oh and to the OP Santa must be married, he he he.

    Good stuff there matey, what crank you running ABA? And i assume you already had the clearence work done on the block? and the machining on the Intermediate shaft for the Oil pump gear ( or am i way off base here?)
    #11
  12. Biglockie
    Offline

    Biglockie Aye you know it makes sense

    Joined:
    Nov 27, 2006
    Messages:
    1,032
    Likes Received:
    0
    To be honest Bryan probably only going to go for just over the 300 mark to start with, goin to possibly 350 tops, think thats gonna be the limit of the GT28rs. Might just keep the APU head then LOL, I'll kep my eyes open for you if your looking for one.

    Been reading that some of the US boys are enlarging the inlet manifolds on these engines.

    on another note, was at my mates gargae the other day he has a rolling road, he was in the prosess of making and elise with an 1.8T lump in it, bored to 1.9 pistons, rods, IHI jabba conversion and being mapped an an emerald ECU, finished at about the 390bhp mark, bloody scary in an elise!!!!
    #12
  13. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    twice in two days!
    Arnold at PAG parts just sorted me out with a vband exhaust housing .......very nice bit of kit.
    [​IMG]
    [​IMG]
    #13
  14. NHN
    Offline

    NHN Modmetractor

    Joined:
    Jan 14, 2008
    Messages:
    27,235
    Likes Received:
    1,220
    :drool: This surely is gonna kick you back in your seat, back seat that is, lol

    Love to see that shoot down a track when down, **** & shovel are 2 words that spring to mind
    #14
  15. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    well I am hoping that the new exhaust housing will drop the spool up by a couple of hundred revs.
    not trying to build some 8000rpm monster.
    its a 5 speed box on a 4wd so I am looking for a decent power delivery down low......and a bigger one up high!

    like the ko3 does but bigger.
    just trying to sort out the wastegate now.
    #15
  16. naefeart_A4
    Offline

    naefeart_A4 Bonkers

    Joined:
    Sep 15, 2006
    Messages:
    156
    Likes Received:
    0
    Very cool stuff.

    Looking forward to reading your step by step writeup jcb, keep the pics coming :thumbsup:

    N
    #16
  17. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    going to do an engine build up when I get the crank back from being dowelled
    #17
  18. Markey
    Offline

    Markey Active Member

    Joined:
    Apr 13, 2004
    Messages:
    2,148
    Likes Received:
    0
    i have a semi :ermm:
    #18
  19. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    jesus!! thats it I feel sick, its all going on eBay!!
    #19
  20. Biglockie
    Offline

    Biglockie Aye you know it makes sense

    Joined:
    Nov 27, 2006
    Messages:
    1,032
    Likes Received:
    0
    Dont ebay it send it to me!!! LOL
    #20
  21. Markey
    Offline

    Markey Active Member

    Joined:
    Apr 13, 2004
    Messages:
    2,148
    Likes Received:
    0
    LOL some very nice bits there mate :) its an awesome project can't wait to see it come together.
    #21
  22. Adam-D
    Offline

    Adam-D Member

    Joined:
    Dec 30, 2007
    Messages:
    457
    Likes Received:
    0
    gonna be a weapon :)
    #22
  23. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    a very stealthy one that looks like a V reg avant with two child seats....... :)
    #23
  24. Biglockie
    Offline

    Biglockie Aye you know it makes sense

    Joined:
    Nov 27, 2006
    Messages:
    1,032
    Likes Received:
    0
    LOL i've only got one child seat in mine fella LOL
    #24
  25. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    [​IMG]

    vband in place
    #25
  26. James333
    Offline

    James333 Member

    Joined:
    Dec 27, 2007
    Messages:
    227
    Likes Received:
    1
    Is this all fitted yet!?!??:thumbsup:
    #26
  27. jcb
    Offline

    jcb Active Member

    Joined:
    Sep 19, 2005
    Messages:
    4,118
    Likes Received:
    13
    build up is running (slowly) in a another thread
    #27

Share This Page