1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Where do i start

Discussion in 'Detailing' started by Quattro_Ollie, Jan 24, 2009.

  1. Quattro_Ollie
    Offline

    Quattro_Ollie New Member

    Joined:
    Jan 1, 2007
    Messages:
    17
    Likes Received:
    0
    i need to clean, polish and protect my pride and joy but dont know where to start in terms of the best products to use.

    For reference i have a silver A6 salon

    :greyrs4:
    #1
  2. quattrojames
    Offline

    quattrojames Moderator Staff Member Moderator

    Joined:
    Mar 28, 2008
    Messages:
    13,884
    Likes Received:
    18
    Have a look at the sticky's atthe top of this thread.
    #2
  3. WX51TXR
    Offline

    WX51TXR Polished Bliss

    Joined:
    Mar 6, 2005
    Messages:
    1,452
    Likes Received:
    0
    ...or this illustrated link in our FAQ...

    http://www.polishedbliss.co.uk/acatalog/car-care-advice-faq.html#4.2

    A good basic routine would be as follows...

    Wash (ideally every week)

    Basic Car Wash Kit - http://www.polishedbliss.co.uk/acatalog/basic-car-wash-kit-wash.html (choosing the Werkstat shampoo)

    Clay (once every six months, to remove bonded surface contaminants)

    Meguiars Quik Clay Kit - http://www.polishedbliss.co.uk/acatalog/meguiars-quik-clay-clean.html

    Polish/Protect (polish every six months after claying, then protect every 4-6 weeks for best results)

    Werkstat Acrylic Kit - http://www.polishedbliss.co.uk/acatalog/werkstat-acrylic-kit-protect.html

    This excellent value for money kit includes everything you need to achieve the Werkstat acrylic finish on your car, and works best on lighter colours and metallic/pearlescent finishes. Werkstat Prime Acrylic is a light finishing polish that lays down a tough initial coat of acrylic protection whilst deep cleansing the paint; you should use it once every six months after claying. Werkstat Acrylic Jett Trigger is a pure spray sealant that should be used to add more gloss and protection every 6-8 weeks; the more layers you build up, the better the finish will get, in terms of both wetness and durability. Werkstat Acrylic Glos is a quick detailing spray and can be used to help boost gloss, lubricate when drying off after washing and loosen the residues of Werkstat Prime Acrylic and Werkstat Acrylic Jett Triggershould you find them hard to remove. Here are full instructions for each major six-monthly detail with the products...

    After washing and claying (and corrective polishing if required), start out by applying a basecoat of Werkstat Prime Acrylic using the white Meguiars Microfibre Applicator Pad. Once fully dry, buff off this residue carefully with the Poorboys Super Thick & Plush Towel, using a spritz of Werkstat Acrylic Glos to help loosen the residue if needs be. To complete the process, apply a coat of Werkstat Acrylic Jett Trigger by spraying directly onto each panel and buffing off immediately with the Poorboys Deluxe Mega Towels, again using a spritz of Werkstat Acrylic Glos to help loosen the residue if needs be. To maintain the finish, simply quick detail with Werkstat Acrylic Glos after each wash, and add a fresh coat of Werkstat Acrylic Jett Trigger every 6-8 weeks until the time comes to start over by claying again.

    :icon_thumright:
    #3

Share This Page