1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Water Methanol Kit, 007p, Strut Brace and other bits

Discussion in 'Classifieds Discussion Area' started by Dannyc87, Feb 21, 2012.

  1. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Hi all,

    I am having a clear out and I have a few parts left from my old mk1 Leon Cupra R. I have very few posts on here but am on SeatCupra.Net with the same name (many posts) and can assure you I am an honest seller.

    AEM Stage 2 Water Methanol Injection Kit: This is one of the best value for money kits on the market, I used it for 7k miles with no issue, bar a broken pump (included). Using this kit I advanced my timing 8.25 degrees with 0 correction factors across the board.
    Included is:
    - The controller.
    - Methanol proof hose.
    - 2 tanks, one 4 litre, and one 20 litre (note that the larger is an adapted water container from halfords, although I used this the whole time I had the kit installed)
    - A check valve.
    - A safety cut off value (plump it in parallel with your n75 and it will cut boost when you run out of methanol).
    - Tank level sensor.
    - A working Devils Own pump (very little use).
    - A AEM pump for spares/repairs (Works intermitently - water damage).
    - 3 injection nozzles + holder.
    - The upper boost hose for a LCR with a port mounted in to for the injector - note this port can be removed and installed in any silicone hose.
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    For all of this (a fully functional kit with spares) I am asking £160 (new kits are around £320).


    I have a Forge 007p available for £45. [​IMG]


    Next up in the Hughes Engineering Rear Strut Brace - this only fits Mk1 Leons. These are known for being a completely reversible installation with simple fitting and removeability should you want to carry large items.
    [​IMG] £45.


    Next is a used Throttle Body for a Leon Cupra R / S3 BAM or AMK engine.
    [​IMG] £45


    Now, an inner CV joint for a Leon Cupra R (these retail at £70 on an exchange basis). BRAND NEW
    [​IMG]
    [​IMG] £45


    Finally, a rear wheel bearing kit for a Leon/Golf mk4/Audi A3 8L. BRAND NEW
    [​IMG]
    [​IMG] £15

    I would prefer all the items to be collected from Woking.

    If you'd like a quote on delivery please PM me. I will also be at the next Ace Cafe meet. Contact via PM please.

    Thanks, Dan
    #1
  2. Ads

    Ads

    [Sep 23, 2014]

  3. s3gazz
    Offline

    s3gazz Active Member

    Joined:
    Aug 11, 2010
    Messages:
    1,263
    Likes Received:
    62
    [Feb 21, 2012]
    Hi dan u got a number pal interested in wmi
    #2
  4. Mitch_TT
    Offline

    Mitch_TT New Member

    Joined:
    Feb 6, 2012
    Messages:
    8
    Likes Received:
    0
    [Feb 21, 2012]
    Ill take the Forge 007p can you send me payment details cheers.
    Mitch
    #3
  5. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Do you want it posting Mitch? If so, can you send £45 + £5 for postage to dannyc87@hotmail.com as a PayPal gift and email me your delivery address?
    #4
  6. Mitch_TT
    Offline

    Mitch_TT New Member

    Joined:
    Feb 6, 2012
    Messages:
    8
    Likes Received:
    0
    [Feb 21, 2012]
    Decided to go ace cafe so ill pay cash then if its ok mate?
    #5
  7. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Sounds good mate.
    #6
  8. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 21, 2012]
    Hi I'll give u £45 for the rear strut brace mate can paypal as gift.

    Matt
    #7
  9. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Wmi sold, forge 007p sold. Matt, £10 for postage okay? £55 posted?
    #8
  10. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 21, 2012]
    Would u do 50quid and I'll pay tonight?

    Matt
    #9
  11. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    £55 lowest..
    #10
  12. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Ah go on then Matt, send the money as a gift to dannyc87@hotmail.com and email me your delivery address. I'll box it up tonight and get it send tomorrow or Wednesday. Cheers
    #11
  13. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 21, 2012]
    Ok will send in the next hour mate thank

    Matt
    #12
  14. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 21, 2012]
    Sent it mate with my address as a note

    Matt
    #13
  15. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Cheers Matt. Just boxed it up, will sort out delivery tomorrow and send you the details. Cheers.
    #14
  16. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 21, 2012]
    Ok thanks
    Matt
    #15
  17. s3gazz
    Offline

    s3gazz Active Member

    Joined:
    Aug 11, 2010
    Messages:
    1,263
    Likes Received:
    62
    [Feb 21, 2012]
    Dan what is the working pump psi wise
    #16
  18. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    150psi.
    #17
  19. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    Matt, the strut brace is being collected by CityLink tomorrow, will be with you on Thursday. Thanks again.

    Gaz, I can get shipping for £15, so £175 delivered. If you paypal the money tonight I can have it with you on Thursday.

    Cheers.
    #18
  20. brasiliangringo
    Online

    brasiliangringo Member

    Joined:
    Mar 22, 2010
    Messages:
    581
    Likes Received:
    6
    [Feb 21, 2012]
    Ive never heard of water methanol injection - what were the sort of gains in your instance ?!
    #19
  21. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 21, 2012]
    WMI has two main purposes - to cool the combustion (lower EGTs so it is possible to run more boost without fuel-dump), and to increase the octane rating. Methanol is the equivalent of ~116RON giving it a much higher resistance to combustion than petrol. This allows the timing to be advanced significantly (8.25degrees in my case)..some guestimates suggest around 3bhp per degree of advance.
    #20
  22. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 22, 2012]
    Strut brace has been collected and is on its way to you. Cheers.
    #21
  23. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 22, 2012]
    Wmi kit is for sale again! Grab a bargain someone.
    Last edited: Feb 23, 2012
    #22
  24. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 23, 2012]
    Offers welcome.. Will be listing everything on eBay in the next few days.
    #23
  25. sambryant
    Offline

    sambryant seat leon cupra r owner

    Joined:
    May 23, 2011
    Messages:
    158
    Likes Received:
    6
    [Feb 26, 2012]
    hi danny, can you pm me your best price for these bits please
    [​IMG]
    #24
  26. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 27, 2012]
    Pm's replied to.
    #25
  27. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 28, 2012]
    Hi mate. I should be getting to ace at around 8:30pm.. I'll be in a white mk2 Leon on BBS CKs..
    #26
  28. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 28, 2012]
    got the strut brace and got it fitted only problem had to replace one of the treads in the end of the brace as it had bin cut so was to short to fit the brace proply

    matt
    #27
  29. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 28, 2012]
    Was it Matt? That how I received it when I bought it (2nd hand). Glad you got it fitted okay. Cheers
    #28
  30. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 28, 2012]
    Mitch, I'm only just getting away from work, not going to make it to ace tonight. Sorry! Will post it out for free for you though. Can you send the money via PayPal gift to Dannyc87 at hotmail.com and attach your address as a note?
    #29
  31. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 28, 2012]
    Yea was a bit of a pain as wouldnt tighten up with the one on it so ad to buy the lengh of thread

    Matt
    #30
  32. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Feb 28, 2012]
    Sorry about that Matt, it tightened up okay on mine :S
    #31
  33. matt88lcr
    Offline

    matt88lcr New Member

    Joined:
    Feb 8, 2012
    Messages:
    10
    Likes Received:
    0
    [Feb 29, 2012]
    When tight in the mounts it was only a tread or two on the bar witch isn't enough Matt
    #32
  34. Mitch_TT
    Offline

    Mitch_TT New Member

    Joined:
    Feb 6, 2012
    Messages:
    8
    Likes Received:
    0
    [Feb 29, 2012]
    No problem will send the money tonight mate.
    #33
  35. Mitch_TT
    Offline

    Mitch_TT New Member

    Joined:
    Feb 6, 2012
    Messages:
    8
    Likes Received:
    0
    [Mar 1, 2012]
    Payment made
    #34
  36. Dannyc87
    Offline

    Dannyc87 Member

    Joined:
    Feb 28, 2010
    Messages:
    38
    Likes Received:
    0
    [Mar 1, 2012]
    Thanks Mitch. It will be sent today.
    #35

Share This Page