1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

SFS supersize K03 TIP

paultownsend Apr 9, 2014

  1. paultownsend

    paultownsend Member

    140
    6
    16
    So my mapped K03 is getting treated to a THS FMIC next weekend. It currently has a PiperX panel, opened up airbox and Forge TIP. 3" decat on the other side.

    Has anyone gone from Forge to SFS supersize TIP? Its HUGE!!!

    Im wanting to optimisemy K03 to see how much it will safely push. Then move to a K03s later in the year.

    Any user information would be greatly appreciated to see if it's woth the move. Also fitting information would be good. I just managed my Forge!

    Paul
     
    Last edited: Apr 9, 2014
  2. Jay A3

    Jay A3 #because Racecar Team Daytona Audi A3 Manual

    2,130
    356
    83
    I went from CM tip to a SFS one last year. Massive difference with less restriction. Well happy with the results [​IMG]
     
  3. paultownsend

    paultownsend Member

    140
    6
    16
    But how was the fitting? My forge is already bl$$dy tight!
     
  4. Jay A3

    Jay A3 #because Racecar Team Daytona Audi A3 Manual

    2,130
    356
    83
    Parsons performance fitted it for me. It was tight and just sits on the lines and I've not had one problem
     
  5. westcoast a3

    westcoast a3 Active Member

    319
    37
    28
    Have this for a while just need to move/ bend the metal pipe a few mil and sorted :)
     
  6. paultownsend

    paultownsend Member

    140
    6
    16
    I have no idea how that will fit!
    So would you definitely say it was a bolt on difference?
     
  7. Grale1

    Grale1 Active Member

    795
    44
    28
    I fitted one to a mates car the other week, it does make a difference and well worth it. But I found it a bit of a pig to fit, I found you can unscrew a a bolt that holds the metal pipe on which will give you some wiggle room, I also found that it was better if you had someone to give you a hand if they fed it from the top and you then guided it into place on the turbo, there wasn't much room but can be done. We also found that a fair bit needed to be trimmed off to get it to fit onto the standard air box, and I'm sure we trimmed a little off when we put the s2000 filter etc on.
     
  8. westcoast a3

    westcoast a3 Active Member

    319
    37
    28
    All I did was remove air box from
    Top look in take old out metal pip to the right bend down and back offer up if not right bend some more fit tricky part is doing up the screw took fifteen mins lol n am a chef :)
     
    s3dave likes this.
  9. A3dubbed

    A3dubbed New Member

    4
    0
    1
    Have you got a link to it??? Cheers
     
  10. antwan64og

    antwan64og Active Member

    811
    207
    43
    Has anyone fitted one over a 3" MAF?

    Ramair filters told me yesterday they wouldn't produce an 80mm version as the market was to small but it would 'probably' stretch over a 3" MAF
     
  11. andy68

    andy68 MORE POWER Silver Supporter

    151
    46
    28

    Here you go, Ramair are wrong,

    K300 Supersize TIP
     
  12. antwan64og

    antwan64og Active Member

    811
    207
    43
    Thats for a ko4 compressor housing outlet of 51mm.
    Ko3 housing has an outlet of 45mm.
     
  13. Jay A3

    Jay A3 #because Racecar Team Daytona Audi A3 Manual

    2,130
    356
    83
    Sfs one fits over the 3" maf fine ;)
     

Share This Page