1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

S3 stage one power gains ?? Your gains ?

Keane May 10, 2014

  1. Keane

    Keane Active Member

    437
    64
    28
    As above what power gains are you looking too see with a stage one custom map ?

    Had a search but can't seam too find anything.

    Cheers
     
  2. Ron burgundy

    Ron burgundy Active Member

    472
    144
    43
    Keane likes this.
  3. batch

    batch Well-Known Member Team Glacier quattro Audi S3

    1,949
    2,409
    113
    I went to Shark HQ, Ben uploaded their generic Stage 1 map then tweaked it to suit my car (has a P-Flo fitted as well).
    Final figures - 314hp and 466Nm. And is a bit of a beast.
     
  4. SparkyMcA

    SparkyMcA Member

    136
    9
    18
    stage one with 466nm, nice!
     
  5. Keane

    Keane Active Member

    437
    64
    28
    Impressive torque ! Think it would be worth me getting an intake then?
     
  6. SparkyMcA

    SparkyMcA Member

    136
    9
    18
    stage one without anything else is it 310bhp 420nm usually?
     
  7. buz

    buz Flat out

    192
    69
    28
    Just stage 1 R Tech remap running V Power produced 309bhp and 359ft lb (488nm) on my 2012 S3.
     
  8. SparkyMcA

    SparkyMcA Member

    136
    9
    18
    nice one, hopefully see that when a go stage 1
     
  9. Muzza80

    Muzza80 Well-Known Member

    698
    330
    63
    Eh, 466/488nm (347/360 ft/lb) from a stage 1 map lol

    If APR can only extract 337 ft/lb with a HPFP, I'm sorry but someone's on the wind up or tweaking those results.
     
  10. batch

    batch Well-Known Member Team Glacier quattro Audi S3

    1,949
    2,409
    113
    Fraid not Muzza, and Ben's dyno is well-known to be one of the most accurate ones running.

    [​IMG]
    EDIT: Apologies, 311.2hp.
     
  11. Muzza80

    Muzza80 Well-Known Member

    698
    330
    63
    I have the same map and essentially the same intake, nobody can "tweak" an extra 60 ft/lb out of a map and it's widely accepted that the stock HPFP cannot flow enough fuel to make that sort of torque anyway, did you not question it??

    I'll tell you what, take it to another rolling road and make the same numbers again, then i'll be really impressed :)
     
    Last edited: May 10, 2014
  12. batch

    batch Well-Known Member Team Glacier quattro Audi S3

    1,949
    2,409
    113
    Better still Murray, if you've already got a Shark map give Ben a call and see what he can do for you! 😉
     
    TomH93 likes this.
  13. gpan

    gpan New Member

    9
    0
    1
    2010 S3 Sportback DSG (in Singapore)

    Mods - APR Stage 1 RON95 map
    APR Stage 1 advertised RON95 figures are 313hp & 314lbft.

    Dynojet 4 Wheel Dyno 20/6/11

    Car dynoed at 255hp and 336Nm (248lbft) at the wheels.

    Using the shop suggested transmission losses of 21%, I got 308hp & 407Nm (300lbft).
    Using Wheel Horsepower to Crankshaft Horsepower Guestimator , I get 323hp and 422Nm (315lbft).


    Dynojet 4 Wheel Dyno 20/6/12

    Mods - Carbonio type intake

    Car dynoed at 259hp and 359Nm (265lbft).

    Using 21% transmission loss, I get 313hp & 435Nm (321lbft).
    Using Wheel Horsepower to Crankshaft Horsepower Guestimator , I get 328hp and 450Nm (335lbft).


    The car is unchanged between dyno runs except for the intake and coincidentally both runs were done on the same day at about the same time but a year apart...freaky! And runs were done at the same shop using the same dyno.
     
  14. Forbzeeee

    Forbzeeee Well-Known Member VCDS Map User Team Sepang Audi S3

    850
    339
    63
    Revo Stage 1 on an S3 8P3 got me 308bhp
     
    Keane likes this.
  15. Dave-S3

    Dave-S3 Active Member

    653
    124
    43
    My car managed 296 Ftlbs stock on a dyno dynamics dyno.. but that was only peak on the day, with a stage 1 remap id probably peak at around 310 ftlbs but hold more torque across the rev band :)
     
  16. Keane

    Keane Active Member

    437
    64
    28
    Nice ! Looking over the 300 mark for sure then how's peoples clutches holding up ?
     
  17. stetheo

    stetheo Active Member

    357
    107
    43
    Some very impressive figures for stage one in here. Don't know what mines pushing out, probably about 300/300. All I know is it drives fantastically and pulls hard.
     
  18. grchmason

    grchmason Active Member

    764
    236
    43
    I agree awesome figures people! :applaus:
     
  19. gilberto

    gilberto Member

    156
    18
    18
    You'll get different results on different dyno's thats a guarantee, it doesn't really matter what map it is, it won't get the same results on different dyno's. My old Evo (with the same mods) was 30 bhp and 50 lb/ft down on a Dyno Dynamics dyno, it was tested on three different rolling roads.
     
  20. S3Alex

    S3Alex Rarely neutral Team Ibis Audi S3

    10,196
    4,263
    113
    It's a while back now but mine was pretty conservative on the figures,and produced around 310bhp and 310ish lbs on Stg1.

    The funny thing back then was that it just about made stock power figures before being remapped,so it wasn't exactly one of the overperforming models.

    The good thing in a sense was knowing that the figures from the RR were pretty much correct(within the usual percentages for temperature etc etc),and each time it's been back,the gains have felt right compared to the actual figures.
     

Share This Page