1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Fault codes

Discussion in 'A3/S3 Forum (8L Chassis)' started by nickelvery, Dec 20, 2007.

  1. nickelvery
    Offline

    nickelvery RS4 B5 380bhp

    Joined:
    Feb 25, 2007
    Messages:
    545
    Likes Received:
    0
    Hi everyone,

    I ran VAGcom and got the following:

    Address 01: Engine
    Controller: 8D0 907 551 K
    Component: 2.7l V6/5VT G 0001
    Coding: 10711
    Shop #: WSC 06435
    WUAZZZ8DZ1N901949 AUZ7Z0Y1578245
    1 Fault Found:
    16825 - EVAP Emission Control Sys: Incorrect Flow
    P0441 - 35-10 - - - Intermittent
    Readiness: 0000 0000

    -------------------------------------------------------------------------------
    Address 03: ABS Brakes
    Controller: 8D0 907 389 E
    Component: ABS/ESP allrad D56
    Coding: 04395
    Shop #: WSC 00899
    1 Fault Found:
    01435 - Brake Pressure Sensor 1 (G201)
    35-10 - - - Intermittent

    Thanks in advance

    Kind Regards

    Nick
    #1
  2. jesters3
    Offline

    jesters3 Active Member

    Joined:
    Jan 6, 2003
    Messages:
    1,516
    Likes Received:
    1
    16825/P0441/001089 - EVAP Emission Control Sys: Incorrect Flow

    Possible Symptoms

    • Malfunction Indicator Light (MIL) active
    Possible Causes

    • Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80) faulty/jammed
    • Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115) faulty/jammed
    • Evaporative Emission (EVAP) Canister Sealing faulty
    • Pipes between Tank Breathing and Throttle Body leaky/blocked
    Possible Solutions

    • Check Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80)
      • Perform Output Test
    • Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115)
    • Check Evaporative Emission (EVAP) Canister
      • Perform Basic Setting
    • Check Pipes between Tank Breathing and Throttle Body #
    01435 - Brake Pressure Sensor 1 (G201): No or Incorrect Basic Setting / Adaptation

    Possible Symptoms

    • Malfunction Indicator Light (MIL) active
    Possible Causes

    • Basic Setting not performed
    Possible Solutions

    • Perform Basic Setting

    01435 - Brake Pressure Sensor 1 (G201): Electrical Fault in Circuit

    Possible Causes

    • Brake Pedal Switch (F) faulty/jammed
    • Brake Pressure Sensor 1 (G201) faulty
    Possible Solutions

    • Check/Replace Brake Pedal Switch (F)
      • See Measuring Blocks
    • Check/Replace Brake Pressure Sensor 1 (G201)
      • ABS Hydraulic Unit (N55) may need to replaced
      • Perform Brake Pump Bleeding
      • Perform Brake Pressure Sensor 1 (G201) Basic Setting
      • Replace Brake Electronics Control Module (J104)
    Retrieved from "http://wiki.ross-tech.com/index.php/01435"
    #2
  3. nickelvery
    Offline

    nickelvery RS4 B5 380bhp

    Joined:
    Feb 25, 2007
    Messages:
    545
    Likes Received:
    0
    Thanks Jesters3, I will check and report back.
    #3
  4. S3 Chris
    Offline

    S3 Chris Member

    Joined:
    Jul 1, 2008
    Messages:
    59
    Likes Received:
    0
    Hi Nickelvery - did you come to a solution for the EVAP code?
    the same one has cropped up on my S3 this week.

    Cheers
    #4
  5. jesters3
    Offline

    jesters3 Active Member

    Joined:
    Jan 6, 2003
    Messages:
    1,516
    Likes Received:
    1
    Do you have any issues with your fuel flap? i.e you get a hissing sound of the pressure being released when undoing the the fuel cap?
    #5
  6. S3 Chris
    Offline

    S3 Chris Member

    Joined:
    Jul 1, 2008
    Messages:
    59
    Likes Received:
    0
    nope i dont get any noise when opening the fuel flap.
    what would that indicate out of interest?
    #6
  7. jesters3
    Offline

    jesters3 Active Member

    Joined:
    Jan 6, 2003
    Messages:
    1,516
    Likes Received:
    1
    It would indicate a buggered gravity valve in the fuel tank, meaning a fuel tank off job to get to it.

    But you haven't got that so all is good!!

    On the EVAP issue, have a look around the canister to see if any leakages are there.
    #7
  8. S3 Chris
    Offline

    S3 Chris Member

    Joined:
    Jul 1, 2008
    Messages:
    59
    Likes Received:
    0
    certainly will do.
    ..... erm wheres it located?!

    you needing an RS3 badge by the way - just noticed your sig and I've got one kicking around the garage thats still in the packet :)
    #8
  9. jesters3
    Offline

    jesters3 Active Member

    Joined:
    Jan 6, 2003
    Messages:
    1,516
    Likes Received:
    1
    Next to the Power Steering Fluid container it has the hoses coming out of it.

    [​IMG]

    Unforunately not as I haven't got an RS3 yet and I doubt I ever will, then again you never know!
    #9

Share This Page