Search results for query: *

To be honest mate im not sure how I left mine after i had the problem, If i was you i would get in contact with rosstech as Sebastian has said below and see if they can resolve

thanks but ive tried that, the SRI function in vagcom goes through each channel and alters in order. I have also tried doing it manual as you mentioned.

I serviced the A3 last weekend and I am having trouble reseting the service indicator. It was on the flexible service, first i used the process as outlined in the handbook (pulling out the button, etc etc) I now realise this was incorrect as it put the vehicle onto the fixed service. I have...

I have updated my above post with more info

I have fitted a set of OEM Bi-xenons to my 2004 A3 I have not yet fitted the leveling kit, i have adjusted the screws on the headlights as high as they will go and they are still not high enough. Is there any coding I can do in Vagcom in order alter the height. All the adjuster motors are...

Don't know why I didn't look before (probably as the cars been at the stealers for a week getting the DSG sorted) but Ive found a blown fuse Fuse 8 Actuators/sensors (engine compartment), radiator fan, main relay for ignition coil Not sure what caused it to blow but it seemed to be causing...

I am getting the same errors as boydie, heres my full scan. I am already looking into the Auto Trans faults, its the engine ones im worried about VCDS Version: Release 805.0 Data version: 20080616 Saturday,28,June,2008,01:55:08:12592 Chassis Type: 1K0 Scan: 01 02 03 08 09 15 16 17 19 25 37 42...

Are we talking about the connector inside the gearbox or the multiplug, ive check both with no joy. Couple of questions please Sebastian Have you got any contact info, email address etc of anyone who has had this problem with the connector or links to any forums?? When you say 'common fault'...

Well I stripped the DSG down again and checked all the connections, the plug inside the gear box has four connections and all these are clean. I have cleaned the contacts on the multiplug on the outside of the gearbox, I didnt find any reason for a bad connection. So its either a connection...

Thanks ill have another look into this, when you say common fault is it the connector inside the gearbox where is plugs ono the mechatronic unit or the plug on the outside of the gearbox. Ill have look at both . Thanks again

Ok ive got an update on this, the vehicle went into audi for a recall and at the same fault was diagnosed and they quoted for the replacement of the gearbox temp/speed sensor. A few weeks ago i set to replacing the Transmission Input Speed Sensor G182. I had to remove the end of the gearbox and...

Is the Mechatronic externally mounted? Its going into audi tomorrow for a recall so ill get them to check it out. Then fit whatever it needs in our workshop.

I have just cleared the faults, (the engine and gearbox would have been cold) and they didn't reappear, drove around and for the first 5 minutes there were no error codes, then when all engine and box was warm the faults returned. It is not doing it all the time, I cleared the codes, with the...

I am having a problem with my 2004 A3 8P DSG Driving along it it felt like it was surging, the car was jerking, kind of its running low on fuel Belew is the VAGCOM report. With the erors highlighted in red Anyone had the same VAG-COM Version: Release 704.1 Data version: 20071016...

Sorted i hadnt coded the engine 01 with 11463 Thanks

i will go and have a look now and post back in 5 min What other coding do you normally have to do other than in the steering wheel 016. DO you have to do any in 001 or 019

When I try to with the new ECU [Basic Settings - 04] Group 060 [Go!] Activate the Basic Setting. [ON/OFF/Next] After a s[Basic Settings - 04] Group 060 [Go!] Activate the Basic Setting. [ON/OFF/Next] After a successful basic setting, field 1 should say "OK".successful basic setting, field 1...

If you have a look at the post i mentioned you will see what i have done as outlined on your website. Think i need to change the slip ring, as i can get everything functioning correctly with the old ECU apart from the cruise. Monday,25,February,2008,22:22:46:12592 VAG-COM Version: Release 704.1...

I am in the process of fitting cruise to my 8P A3 I have had a few problems still trying to sort http://www.audi-sport.net/vb/showthread.php?t=50614 My question is what coding should be done? I have coded (16 Steering Wheel) 0011142 (auto, no multifunction, paddles, on board computer...

Yesterday my A3 8P parking assist started playing up, When you put it un reverse you get a long beep then nothing. Manual states if you get this there is a fault. Just Vagcom check and get the following. Monday,28,January,2008,21:05:42:12592 VAG-COM Version: Release 704.1...