Search results for query: *

Hope this is fine being in this forum, but I've got a 2006 petrol Octavia VRS (2l TFSI BWA engine) with engine troubles. Recently the turbo blew and this has been replaced with a OEM one from TPS. Renewed the required lines as well and the removal and refitting went fine. After starting it and...

Plugged my car into VCDS the other day as the EML light came on and performance was greatly reduced. I got the following error codes: 3 Faults Found: 008801 - Boost Pressure Control Valve (N249) P2261 - 008 - Mechanical Malfunction - Intermittent Freeze Frame...

On idle the engine in my car is hunting and not staying at a consistent rpm. Under load the car is fine and the revs rise and fall as they should. It even stays ok when I shift into neutral for a brief moment after being under load. But if I were to stop with the engine running, within 30-60secs...

anyone here had to replace their intake camshaft on the 2l tfsi? Upon changing my cam follower I decided to see what revision camshaft I had fitted and unfortunately it's revision 'a'. So along with the latest revision camshaft I'll be replacing the follower (again), timing chain and tensioner...

Had my blue haldex on now for 6 weeks or so and more recently I've noticed I've lost circa 50-60miles to a tank doing the same journey. Would I be right in thinking that maybe the blue haldex is the cause? For those who have one fitted did you notice this?

Anyone have these fitted? How are they?

Fitted s3_dave's adjustable rear tie bars recently and have managed to get the headlight levelling sensor bracket fitted by packing out the excess gap. Is there a more permanent option available to safely secure this piece? Those of you with Dave's tie bar's what have you done?

Anyone know the torque value for the hex head bolts on the silver project camber plates?

I'm in the process of taking off my front hubs to get new wheel bearings pressed in. I've managed to undo the tie rod end, undone the top nut on the balljoint, and removed the strut from the hub carrier, however the hub just won't budge along the splines of the driveshaft. Is the only way to get...

I need I get the following connector replaced as it has snapped on the release tab Are there any tools to release the connector pins or is it a case of chopping the wires off and soldering the new part? Ideally I'd like to avoid chopping the wire.

On the rear I've read 1.10deg negative camber is ideal (I have RATB), however what is recommended for the front? I have Silver Project camber plates being fitted.

I currently have a Valeo branded alternator fitted. I've replaced the volt reg and still no charge getting to the battery. Also I replaced the battery and checked continuity on the cable and still no joy. So this is leading me to believe the alternator is at fault. Could I change from a Valeo...

Have a set of Dave's RATB's and some Silver Project top mounts to be fitted. So far my list of parts that I'll also need is bare with just a couple of bearings for the top mounts. Can anyone help with gathering a list of any other items that I may need for the top mount and RATB installation...

This is with regards to the mk1 TT however I thought there would be more chances of getting replies on the post here as it's busier then the TT boards. Also essentially underneath the bodywork they're the same car (or near enough). Has anyone got any experience with them? AUDI TT MK1 TOP MOUNTS...

Cam chain tensioner gasket is leaking so I'm looking to gather the required bits during the week for a go at fixing it over the bank holiday weekend. Aside from the cam chain tensioner gasket, the half moon gasket and the tensioner tool (3366) is there anything else I should be purchasing?

Has anyone any experience or view on using both adjustable tie bars & camber correction bushes (the likes of which are sold by Superpro)? Not necessarily the camber correction bushes on the adjustable tie bars but maybe adjustable tie bars fitted in either the top or lower position with the...

Hello all, Hopefully picking up a 2003 1.8T tomorrow and am just wanting to clarify something with regards to the various 1.8T engines that are on offer. Previously I had been looking at MK4 Golf GTi's and found out that the AUM engine was fitted with the K03S turbo unlike the AGU which was...