Search results for query: *

Hi ive recently put a second hand engine in my s3 8l i installed the cam belt myself going off the marks to a previous belt install ive changed the cam position sensor of my old engine and replaced the crank sensor but it still keeps coming back although the car seems to be running spot on ...

Morning all i've recently had to put another second hand engine in my s3 as the cambelt went since the new engine has been in i keep getting the code 17748 cam position sensor ive changed it and the crank sensor but it still keeps coming back car is running perfect cant understand it anyone else...

ive done a bit of research and its not the siren noise car boosts well and still pulls like a train its more of a blowy happy noise its so hard to describe , there's no smoke from exhaust , im stumped , got a fault code on the n80 evap valve which im going to replace , take it from there , I...

yes it is could it be the dv solenoid ?

it was the original dv I put back in and yes it was in good condition no rips as for the sound clip I will do it shortly and nothing else has been disturbed it only started doing it a couple of days ago I don't drive it that much and usually have radio on but ive kept radio off to listen

hi all my s3 8p seems to be getting turbo flutter noise and like a tapping screeching noise when on boost I have the dv+but the rubber piece has come off the front where it faces down into the housing , ive put the standard one back on to see if it made any difference but still muttering and...

hi does anybody know them part number for the cam position sensor on the s3 8p 08 model please got code 00010 (bank 1 intake ) slow responseP000A not a plausible signal intermittent

Hi all I have changed my rear callipers and pads as the callipers were seized , had to change a rear brake pipe, near side rear, ive bled the system and the master cylinder but my handbrake light is staying on. goes out when I apply the foot brake, What could the problem be ? ABS NEEDS...

thanks for the info but ive given it up as a bad job

Hi all has anybody got any info on how to install a double din unit into my pre face lift s3 ? ive tried but theres an extra plug next to the heater controls which controls the up and down fan speed which mine dose'nt have and also what happens with the rear heated screen plug as its again...

Hi I bought a maf sensor from TPS around 12 months ago and it keeps throwing up code 16487 , ive been back to them and they said I need to take it onto Audi for them to check it and if its not faulty I have to pay for the diagnostics , it docent show up all the time but more than not could it be...

hi all asking for a friend as im an 8l owner going to look at an 07 plate with 88,000 on the clock tomorrow what should I look for in regards to quality and condition please, any help would be much appreciated thanks

hi all my oil light came on the other day twice in about ten minutes but then went off , I checked the oil level which I knew would be ok as I only changed the oil about a week and a half ago , the next day it came on with three loud beeps and did it twice but stayed on for a minute or so , I...

like to ask a question ! will any narrow band pre cat lamba sensor work on an APY or does it have to be the exact one for the APY ? TPS don't sell them anymore for my car and at £207 with the dreaded im glad robbing **okers

<tuffty/> you wouldn't happen to know the size of the bolt to blank the egt sensor off on the back of the turbo would you ?

thanks for your reply tuffty kinda what I was hoping to hear really

Hi just after a bit of advice -information my car started out as an 210 apy the engine went knackered so it was replaced with a bam engine and this has the vvt on it, if I get a bam engine loom and ecu to get the vvt working would it run better ? ive just had my turbo changed and the lad who...

this is why I ask on here first as you guys have the knowledge and stops me from making big mistakes thanks very much for your time guys much appreciated

are all the pistons the same ?

hi all ive been looking for a BAM block to do a forged bottom end and I think ive found one , but it has a knocking rod , will it be ok to use ? as a base for a forged engine ? any advice would be much appreciated