Search results for query: *

  1. mattyb6

    Low compression

    I will have a think on what I want to do, I would do a rebuild if I was going to do rings etc If not, the brother can buy it
  2. mattyb6

    Low compression

    Yeah mate the cams and follows seem fine, I know you can't be 100% until the head is off but the chain and belt all seems fine aswell, So all in all the lump seems to have been looked after to a decent degree I might start pulling it apart this week
  3. mattyb6

    Low compression

    After a breakdown last week And some research and finally a compression test today it's official Low compression on all cylinders Results: Dry. Wet 1. 45psi 96psi 2. 95psi 250psi 3. 50 psi 150psi 4. 120 psi 175psi To be fair I did put a little bit too much oil into cylinder 2...
  4. mattyb6

    possible DMF failure

    I need the clutch kit today if possible so don't have time for bill to send me one, So oem all the way Il look now
  5. mattyb6

    possible DMF failure

    I was thinking last night I think I'm just going to oem And for that reason you mentioned, some people have loads of power and are fine so I will be
  6. mattyb6

    possible DMF failure

    after doing more research... 1. (if it fits) abf flywheel + vr6 clutch 2. oem DMF + clucth kit ( will this cope with my future plans)
  7. mattyb6

    possible DMF failure

    just broken down, which what i thought was limp mode. the car kept loosing drive but not engine power, felt like sticky vanes from a pd130 engine. anyway i pulled over, engine ticked over with no bangs, leaks or warning lights. i turned it off, gave it the once over, went to turn it over and it...
  8. mattyb6

    Clutch kit?

    Vibration through gearstick I've got vibration when using the clutch to move off No whining or nothing from the box, and pulls fine so guess it could it the dual mass
  9. mattyb6

    Clutch kit?

    Just to hijack What would be the symptoms of a worm dual mass ?? I'm getting bad vibrating when pulling away slowly
  10. mattyb6

    3" downpipe on a driveway

    Got a few bits of tools mate, so should manage in that aspect. It's the access part in more unsure about, btw I have a Quattro sport with a either a ko3 or ko3s. I didn't wanna drop the subframe or anything tbh, I was going to take the drivers front wheel off as I heard you can get it out...
  11. mattyb6

    3" downpipe on a driveway

    Good answer mate Ha Just been out, had a look, I've git axels stands and ramps, and got all weekend to do it. So shouldn't be too hard. Il just need to buy a 3/8 drive universal joint lol
  12. mattyb6

    3" downpipe on a driveway

    Found the answer so can be deleted
  13. mattyb6

    3" downpipe on a driveway

    can the 3" downpipe and decat be fitted on a driveway with Ramps? Without dropping the subframe ? Might do it tomorrow if possible, if not il have to wait lol
  14. mattyb6

    2" boost pipes yes or no?

    Bill I never knew the stock pipe size hence the question. I totally agree and understand that bigger within reason is better. Il probably stay with 2.5" for now until I can't get some custom ones made up
  15. mattyb6

    2" boost pipes yes or no?

    Thanks prawn Well my goal was about 230-240 ish. The inter cooler I was going to buy was toyosports eBay one, https://www.ebay.co.uk/itm/310204072487 Out of stock at the minute. The budget is the main concern really. Although I can go for 2.5" pipe, i was looking at an eBay kit again...
  16. mattyb6

    2" boost pipes yes or no?

    I didn't know the oem pipe size, but yeah totally agree Il stick with 2.5" You don't ask you don't know I suppose Thanks
  17. mattyb6

    2" boost pipes yes or no?

    I'm not aiming for mega power, on my 20vt qs I'm ordering an fmic tomorrow and I have several metres of 2inch stainless lying around and was wider in if it would be suitable?? Only mods will be 3" DP and decat, sfs tip, forge oo7p, and a fmic... And a map of course. What size is the boost...
  18. mattyb6

    Ko3 tip confusion

    Mate is the one you're on about https://www.ebay.co.uk/itm/351246459809 I've just seen the forge ones on awesome gti which seem a bit over priced
  19. mattyb6

    Ko3 tip confusion

    Cheers bill, does a ko3 tip fit ? Or if not what are people using?
  20. mattyb6

    Ko3 tip confusion

    It's time to start gathering some parts together but I have a problem with getting the right tip I have an ARY engine code 2001 a3 QS I believe it's a ko3s but not 100% sure, so does a ko3 and ko3s share the same tip? And is bill at badger the best place to get one?