Anyone here with a Unitronic Stage 3 TTE700 DAZA Stock engine?
I am considering this stage and would really like to hear from some already on this stage.
If you have acc then make sure you have new screws to mount it. They forgot to send them to me when I ordered so I had to improvise
Sent from my iPhone
You have revo on your rs3?
My first tune on mine was revo but I logged some strange n75 dc behavior and boost was hit and miss all the time.
Did you log yours to see how it performed?
Here is a revo log and after I removed it I went with unitronic and did same logging.
Usually n75...
Would love to see your 1/4 mile time on this setup :) My best so far is 11.0 sec and I was hoping to go into high 10 after I did the dog bone insert.
FL??
I assume every car in this thread is the 400hp Facelift version. Anyone here have the older 365hp car?
Also since I have been hanging on...
I don’t think you can find any thing as bad as the stock cooler.
Evo1 (not the older one) has a core volume of ~13L compared to the stock 8.3L
Here is a 4th hear pull at 14c ambient with same start and warmup.
You will of course find upgrades that is better then the evo1. I went with the...
That makes your result more impressive ;)
Do you have access to 98 or 99 ron?
If you kick your passenger and say 1/4 of a fuel tank you could probably go very low 3 using 97 with a drop of e85 (like an e20 blend)
Or perhaps you are lucky and can see a 2.x sec ?? :)
Sent from my iPhone
What tune do you have and what oct are you running? I assume you are at stage 1 or 1+
Here is mine at 3c and 19c tuned with Uni 1+ running 98 ron. I do have an apr inlet combined with a k&n panel filter and evo1 ic upgrade
Sent from my iPhone
My first tune in my rs3 was also revo and I could see above 6 degree of timing retardation under wot. This was with an ambient temp of like 10c.
I could also see some strange wg dc when I logged my car.
After switching to unitronic then everything was normal and I logged max 1 degree...
Yes I have installed it.
It took me about three weeks from start to finish including the wait time. I needed to order some new tools and some parts. I could not save the small stock hose connected to the turbo outlet.
Also the washer on the inlet looks like a one time use washer so I had to...
When my RS3 was stock my slowest 0-100km/h was 3.86 sec. That translate to 3.71 sec 0-60mph. I could not believe my eyes when I watched that video showing the RS3's 0-60 at 4.2 sec. That is like 0.5 sec slower compared to mine. I always use 98 Ron fuel (93 Oct) so I was wondering if they could...
Hi
I have the evo1 on my rs3.
Installation was straight forward and temp dropped some degree.
I was only able to compare at 14c ambient with unitronic stage 1+
Here is a 3rd gear pull over rpm
Here is a 4th gear pull over rpm
And here are both the 3rd and 4th gear pulls with some extra...
"remap the gear" Like a TCU flash?
By looking at my torque I would assume that the torque climbs above 480 lb ft. VCDS just takes samples and it might have missed the point where the torque goes to high.
So the big question is if the clutch is actually slipping or this drop is the ECU cutting...
Do you have any other mods?
I have the APR inlet pipe + elbow and a K&N panel filter but I don't think these parts should make to much of a different.
Here is a log over time showing the RPM increases for so to drop again where the torque is peeking.
And here is another log over time where...
I am in 4th gear when this usually happens (video is recorded in 4th gear) but I also notice it in 3rd gear when WOT from 3000 or 4000 RPM.
The revo map that was flashed to my car is the 97, 97 low boost and 98. I just switched to the 98 Ron map (since I always use 98 Ron fuel) and I see now...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.