Search results for query: *

  • Users: S3Zek
  • Order by date
  1. S3Zek

    Both Rear Calipers appear to be seized when trying to change discs

    They tend to cerode badly inside the lip where the dust seal sits in and also under the piston seal, this then pinches the piston like its seized, a good scrape out inside the seatings were both seals sit in and all around the top lip to remove any built up crap then clean the outside of the...
  2. S3Zek

    Rota GTR's on an S3?

    Cheers for that lads, I'm looking at getting the rota force grids on a 18" 9" et35 so I can play with spacers for the right look but didn't know if I could get away with a 245 40 rather than a slight stretch on a 235 40. Dose anyone have any picks of a 18" by 9" rim with either of those sizes...
  3. S3Zek

    Rota GTR's on an S3?

    Sorry for another revive but dose anyone know what the tyre size was on the last set of picks on those18 by 9.5" as there on a slight stretch.... Cheers
  4. S3Zek

    Sachs paddle clutch plate

    will dig out the bill for it later for you as I can't remember lol, I went as far as I could go with a hybrid apart from water meth and cams in the end as far as I'm aware so I hope it will cope with the early toque.
  5. S3Zek

    Sachs paddle clutch plate

    That's the kit I bought, got it direct from Sachs, it dose make the box chatter a bit on idle but it's got a good bite to it, feels like a paddle as it's got a strong face plate so is a little heavier on the foot, if you want to upgrade it to the next up its the same kit but comes with the...
  6. S3Zek

    dose anyone have any ideas on this???

    Newmarket, Suffolk
  7. S3Zek

    dose anyone have any ideas on this???

    The rear light did start flickering abit so I just unplugged it just incase it was something to do with one of the LEDs, but no...... did try slamming the doors....just in case lol
  8. S3Zek

    dose anyone have any ideas on this???

    Yes it drives fine and all the warnings go away when started, it's just the fuel gauge that craps out when it's running. No not scanned yet, I don't know anyone this way with vcds and I don't have the cash at the min for Audi prices, plus got to get to a test tomo,I
  9. S3Zek

    dose anyone have any ideas on this???

    tried the search bar but no luck
  10. S3Zek

    dose anyone have any ideas on this???

    HI all, right, sitting outside drinking a cup of tea in the sun and my car alarm gose off.... hmm walk over, open car, shut car, lock, walk away and back to cup of tea.... Alarm gose off again, walk to car open car then notice dash back light is on and it then starts beeping at me , big red...
  11. S3Zek

    Steering wobble :-/

    Have you changed the lower arm ball joints as this happend on my mates, no movement when jacked up due to the angle but only a very tiny amount of movement when down ment it felt like it was all over the place.
  12. S3Zek

    Possible alternator issues

    i did all mine when i had that fan fault
  13. S3Zek

    Possible alternator issues

    good scrub up wouldn't go a miss at the points and the ring ends by the looks of it, I would do the earths to the block and the starter while your at it. but from what your saying I would change the alternator if its not putting out around 13 or over when loaded up
  14. S3Zek

    Come on down and post your mileage please

    Bam on 127000 clutch dieing (was/is still strong just not in car) New agu lump with go faster parts and lots of other crap 3x for 10 seconds with only down pipe on last night :) lol And no leaks (yeay!) yet!!
  15. S3Zek

    Rear adjustable tie rods got to mad not to

    Had these since the end of 2011 or begining of 2012 from dpm performance http://www.dpmperformance.co.uk/comp-brake-adjustable-rear-tie-bars-control-armsbr-s3-8l-18t-quattro-0199-p-7250.html and they still have no play in them and they havent broke yet as i drive quite sprinted lol so there not...
  16. S3Zek

    Just got this back from relentless.....

    Cool will do then, :) And thanks gazz I must of had one of the first v3s before then.
  17. S3Zek

    Just got this back from relentless.....

    Ok, do you know what the v2 was by chance?
  18. S3Zek

    Just got this back from relentless.....

    Just showing it as the tubing looks a little bigger and there is more joins on this than I had on the first one, is it just a case of making sure you have it spot on with the head.
  19. S3Zek

    Just got this back from relentless.....

    I suppose as long as it fits its a better start than last time.
  20. S3Zek

    Just got this back from relentless.....

    Just got this back from relentless in exchange for the v3 that didn't fit well, Then spotted peeps on here discussing the v3 isn't as good as the v2 for flow but is stronger! So I thought FSS who wants my v3 as I shall now get a v2 and have it braced up........ Well today I opened the box to...