https://www.google.co.uk/url?sa=t&source=web&rct=j&url=http://www.devtechnics.com/winlog.htm&ved=0ahUKEwiYrIiJ8qPQAhVY-GMKHah7BlUQFgghMAE&usg=AFQjCNGhNT9Eu6AE6aBlK3xTh8SXRnr04Q
With a custom driver
The issue with eBay turbos are they poorly balanced, like very badly. Generally the parts are ok and even bad parts will be ok of balanced well but they aren't so fail.
You may need to port the turbine housing as well so in reality although they are cheap they aren't ideal and by the time you...
You did have the preproduction one. Was the very first one done and very different to the ones made now. Definitely trying to find our feet with yours as people kept saying it wouldn't work, couldn't be done blah blah blah..
I'm impressed it's lasted as long as it did anyway and is was designed...
More than likely the turbo is out of its effeciency range and either heating up the air.
Boost has a direct relationship between speed and volume. So the same avolume of air moved faster will be at a higher pressure than than of the same air at a lower speed. It's why a gt35 at 25psi flows more...
The turbo is loosely based on a k03 tfsi from the 2lt engine in terms of internals, it can be upgraded to the larger k04 turbine and the k04 1.8t compressor wheel and should be good for 300bhp if allowed but everything else will limit it before it reaches that figure.
Single feed has 1 hole. Oil is fed from the bearing housing into the journal bearing under pressure by this single hole. Oil enters the bearing and moves outwards via the small grooves along the bearing supporting the shaft and exiting the bearing at the ends.
Twin feed has 2 holes, 1 at each...
Who is the eBay seller? Well known or trusted?!
Fit it at your own peril but believe me it's not worth doing and won't in any away give more more oil flow, actually less!
Why? Well look at the bearings. Single has 1 hole room feed inside the bearing and then grooves along the bearing to feed...
Turbine housings bolt to manifolds
DP flanges need changing
1 housings needs the actuator arm moving
Compressor housings need to be cut and shut to match rs4 or use a set of rs4 ones.
Actuators needed as well ( to a certain point)
Mainly labour to convert and really do well with an upgrade...
Spdt
Double throw going to single pole.
So signal wires from the 2 sensors go to the 2 throws and single pole goes to device.
I've got a link for the device which has a diagram for the sensors I listed but I can't link so I'll send it over.
Nick
Why not just buy 2 wire (actually 3 pin) knock sensors
0 261-231-038
Then fit 2 and use a switch to change between the 2. Then you have 2 knock sensors covering 4 cylinders.
12 volt and signal wire is all that's needed.
I used a knock detector I got off ebay for £40 and 2 of the...
If you plan on doing yourself it's not too expensive, £25ish for pickup and o ring, then oil and gasket sealant. However, a4 is a pain to drop the sump. Ideally subframe needs to be dropped, but it can be done by lifting the engine up. If a garage will do it for £250 I'd get them to do it, alot...
Won't be the maf readings or scaling. Even a Hta30 running 495bhp on a 3" s3 maf has no issues once it's above the maps 292grams limit. All that happens is the axis stop and last values are used. O2 should remain closed loop regardless and only go open when a variable bit which controls a...
Yes of course. If any of the protection systems kick in or the adjustments come in then it will go open loop.
BTS is a prime example of this, it ignores the 02 and just dumps fuel.
Timing CF is what is actually being meant. This is the amount of timing the ecu is pulling from the maps value in order to prevent knock. Tuner should know this really and how and why it happens/prevented.
Fuel grade 99 v 95 will give a different cf. A faulty maf giving wrong air flow also...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.