Search results for query: *

I just had the car at the dealers, and they changed the thermostat. However, I havent had issues starting the car for some time before the change or after. Another issue is that the temp in the dashboard never reach 90C, It stays between 70-85 somewhere, whatever the temperature is outside. The...

Been AFK for a while. :thrashi: My lower amplifier is 8P4.035.225, and according to ETKA I can use this amp for Concert. :) But I have to disconnect the second coax wire from the HU, and extend this to the upper amp which is a 8P4.035.225.B. So I need to make an adapter from coax to a 3-pin...

Thanks! :respekt:

Is there some way to enable default instrument lighting through vag-com? So I can just turn the key to get the lighting on. I've searched through the programming, but can't seem to find the option. :keule:

I'm betting it is the sensor. Just talked to the dealer, they where thinking the same thing. Next time it happens I'll try to get some readouts from vagcom. :)

Over the last 3 weeks, I've had problems starting my car a few times. I turn the key, and the motor starts like normal, when I rev the engine it dies. I start it again, and it won't ignite as normal. I have to keep cranking the engine for a few seconds, and it will start again, but will die when...

Hm. From what I can see, I need either 8P0 035 225 or 8P0 035 225G. Nice illustration :sm4: I'll check whats in my car tomorow

This is the r-108 amplifier? I see from elsa that the two pins from the HU goes to r-108(aerial module) and r-24(high freequency aerial amplifier). As on my current system, both cables goes to r-108. This means I would have to do some rewiering back there. But I guess the r-24 is the same on all...

Thank you for the very informative answer. If I was to install the new antenna amp, do I need dual antenna-wires from the tailgate? What did the new amp cost?

I have just bought a new(er) 07 concert3 head unit instead of my symphonyII(05). I was hoping to use the same connectors, but no such luck. The DIN power connectors are different, but that is just a matter of wiring, what I am trying to figure out is how to connect the antenna. Could someone...

NHN. The coding I used for the main beam: Long coding Byte 00 Bit 1 ON Byte 03 Bit 4 OFF Byte 17 Bit 1 OFF As far as I could see, there was 20 bytes programmed... Don't know if that means anything. Matt. When I flash in the off position nothing comes on, maybe the drls would have come on, but...

After some browsing I found out how to get the full-beam to work, and I programed the fog-lights to work as daylights :) Its a good feeling to finally put everything back together. :) Thanks for all your help guys!

Thank you for the answer. Yes. I have been working on the car all day, and so far I have got everything running,except daylight and high beam. I was thinking of tracing the wires as you said, but after the high-beam on the xenons didn't work, I was beginning to think that the instructions were...

Well. Finnally have the time to continue installing these xenons :) Sensors, looms and the autoleveling control unit has been installed. But so far I have encountered a problem. Where to connect the daylightscables from the kufatec Bi-xenon adapters? The pins refered to in the fitting...

@mattandrew I'm affraid what I am looking for is the pin connectors(which ones) to the boardnet from the autoleveling control unit(top left on the picture below)and from baordnet to the bi-xenons(from the adapters). Kufatec supplied an adapter from the original contacts in the...

I was planning on getting the Com. But as my car has can-bus, the equipment was quite expensive. But I guess I will get it sooner or later. :) All cables and everything in the car is finnished except actually putting in the xenons and connecting cables to boardnet, fusebox and gateway. Im...

This is pretty new for me, so please bear with me. :) Drl is daytime running lights? Yes, the dipped beams ignites when I turn the key. In my country we have to drive with lights on in daylight, so most cars come with dipped beams on as standard from the dealers. Boardnet H34 / S0301 8p0 907...

Hi all. I was hoping someone could help me with some issues regarding the wiring for bi-xenon and autoleveling(halogen to bi-xenon) as there seem to be many knowledgeable people here. :respekt: I have the cabling and components from Kufatec. The thing is that the fitting instructions kufatec...