Happy Grumpz
Registered User
- Joined
- Jun 2, 2016
- Messages
- 568
- Reaction score
- 710
- Points
- 93
- Location
- Tyne & Wear
- Website
- www.mahalkitaphotography.com
Ive just bought the LED ring and wiring for this, hopefully I'll get it in the next week or so
Its a bit of a pain getting the peg type jointing things disconnected but if done carefully its not impossible.Ive just bought the LED ring and wiring for this, hopefully I'll get it in the next week or so
Its a bit of a pain getting the peg type jointing things disconnected but if done carefully its not impossible.
I melted them a bit with a soldering iron and used a sharp chisel and pryed apart the two surfaces with some of those special plastic trim tools. Heart in mouth a bit as I feared I might buckle the top section but it came apart eventually. I used a glue gun to re-install. I obtained the wiring loom from the K electronic shop (German site) as I wanted to wire into the infamous fuse circuit so as to utilise the mmi. I didnt do it personaly but took the whole lot to a proffesional outfit who do these LED retros but do charge a whacking price But tbh the guy took a very long time trying out codes to get it to talk with the mmi and got there in the end thankfully. Happy bunny but broke
Wished to hell I checked carefully when I specced when I ordered but it was a bit misleading
Best of luck with your project
Sure, Here you go. Hope it helpsHi @SRT do you mind sharing some photo of the controls on your MMI screen?
Sent from my iPhone using Tapatalk
Well tbh I just have everything up full but yes I guess front would include the cupholder. Not really played around with it so far but I am sure others have?Thanks mate, I would assume "front" controls the cup holder light?
Sent from my iPhone using Tapatalk
Well tbh I just have everything up full but yes I guess front would include the cupholder. Not really played around with it so far but I am sure others have?
Sounds like a coding issue or earth?Others' experience on the MMI is welcomed. The reason I am asking in such detail originate from the frustration of being able to enable the "front" selection but my cupholder still remained unlit.
Sent from my iPhone using Tapatalk
Well, the parts arrived today, I followed the instructions in this thread, deliberately changing the wires around so it would be red...
To be honest, the hardest part was getting the centre console off, the rest was really straight forward. I used a Dremel to get the 1st 12 tabs off, prised it open, swapped the parts over then just glued it back together.
Really pleased with the results.
Looks good Tim.
Here are the bits I sent him and I also pre made the loom so was ready to rumble more or less. Doesn't get much easier than that.
PM if you would like it too.
View attachment 100521
i really want to do this but I'm not that brave to take apart the dash and get death rattles.. really how easy is it to rip apart the console?
anyone in the hampshire area that fancies do this with me? beer tokens WILL be provided as standard
Just been in to Belfast Audi to order the LED rings for this, none in stock so should hopefully have them next week. The weird thing is though, it only came up as being £16.82 on the system? I thought they were about £35?
Sent from my iPhone using Tapatalk
Part list needed for the cup holder light mod.
8V0 947 157 A
8W0 971 832
000979009E
000979940 x 2
@TimWills28 your invoice shows 4E0972575 too which already came supplied with the light, (ETKA didn't tell me this), however I included 2 butt connectors for you instead to make up for it
Cheers
Mike
I see you have a menu for 'exterior lighting' there too. I don't have this in mine, what all can be adjusted/controlled from it?
Sent from my iPhone using Tapatalk
That would be why I don't have it then lol, no auto lights!
Sent from my iPhone using Tapatalk
Installation has begun!
Sent from my iPhone using Tapatalk
Installation has begun!
Sent from my iPhone using Tapatalk
Easy peasy
Ditto!
Currently sat in the car trying to remove the cig lighter unit so I can take it inside and wire it up...
Anyone any idea on how to remove it?
Sent from my iPhone using Tapatalk
BTW I've been following your video @TimWills28 Great stuff! It's been super helpful!!
Thanks for uploading and keep up the good work
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Dremel made light work of the little tabs, had all 12 removed in less that 10 mins! Glued it back together with some Dow Corning 3145 silicon. Only installed the rings today, will do the wiring in a few days when I have a bit more time
Sent from my iPhone using Tapatalk
Good stuff, dremel always easier option for something like this...
Sent from my iPhone using Tapatalk
Yeah, was a piece of cake! Got a couple of nice little bits for it from work too, little ball cut right through the tabs, then the abrasive cone tidied up and scuffed the area for gluing!
Sent from my iPhone using Tapatalk
I really want to properly wire this in so it can be controlled through the MMI. Is it worth the hassle and amount of work involved? I'll be installing the footwell lights soon too
Sent from my iPhone using Tapatalk