Hello All,
I am relatively new to this board, and require some very urgent assistance with my A6. I have searched the forums and have found nothing conclusive.
Basically I had the notorious G201 Brake Pressure sensor fail in my abs module. I wasn't aware at the time of services such as BBA Reman & Module Masters at the time, so I purchased a 2nd hand unit on ebay.
My original ABS module part number was 4F0614517L, as inscribed on the hydraulic unit. The part I purchased has the identical part number as well.
I changed the units out and bled the brakes, only to see a few different trouble codes appear. See here;
-------------------------------------------------------------------------------
Address 01: Engine (AUK) Labels: 06E-910-559-BKH.lbl
Part No SW: 4F1 910 559 C HW: 4F1 907 559
Component: 3.2l V6 FSI 0010
Revision: --H15--- Serial number:
Coding: 01050400190F0120
Shop #: WSC 02325 785 00200
VCID: 2B53BF628AE505461EF-807E
3 Faults Found:
18061 - Please check DTC Memory of ABS Controller
P1653 - 008 -
Freeze Frame:
Fault Status: 00101000
Fault Priority: 2
Fault Frequency: 43
Reset counter: 193
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:08:17
Freeze Frame:
RPM: 1056 /min
Mass Air / Rev.: 130.8 mg/str
Temperature: 42.0°C
Idle
Load: 16.9 %
Speed: 0.0 km/h
-------------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 4F0-910-517.lbl
Part No SW: 4F0 910 517 L HW: 4F0 614 517 L
Component: ESP 8.0 quattro H03 0090
Revision: 00000000 Serial number: 00000000000000
Coding: 0020875
Shop #: WSC 02327 785 00200
VCID: 2D57B17AB4F10B7600B-8078
5 Faults Found:
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 39
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:42:56
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x47A2
Hex Value: 0x001E
Hex Value: 0x3EAC
Hex Value: 0x00FF
01321 - Control Module for Airbags (J234)
000 - -
Freeze Frame:
Fault Status: 11100000
Fault Priority: 1
Fault Frequency: 38
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:34
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x309C
Hex Value: 0x00FF
01314 - Engine Control Module
000 - -
Freeze Frame:
Fault Status: 11100000
Fault Priority: 1
Fault Frequency: 38
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:35
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x319C
Hex Value: 0x00FF
18055 - Check Coding of ECUs on Powertrain Data Bus
P1647 - 000 -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 37
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:35
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x209C
Hex Value: 0x00FF
01486 - System Function Test Activated
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 3
Fault Frequency: 36
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:49:54
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x47A2
Hex Value: 0x0021
Hex Value: 0x4194
Hex Value: 0x00FF
-------------------------------------------------------------------------------
The G201 Brake Pressure sensor error has gone, and my cruise control works again - so im inclined to think that the module/pump i fitted works. Now when I start up the vehicle I get 3 loud beeps for brakes - and the lights continually flash when driving.
I have managed to clear the steering angle fault (00778), and the System Function Test (01486)
I cannot clear 18055, 01314, and 01321.
Anyone with any assistance or information on how to do this would be greatly appreciated.
I have mailed the full autoscan to Ross-Tech but I didnt receive any feedback from them - I do own a genuine vag-com hex-can-usb cable purchased from hexdiagnostics south africa. So I am a bit stuck for help.
I am relatively new to this board, and require some very urgent assistance with my A6. I have searched the forums and have found nothing conclusive.
Basically I had the notorious G201 Brake Pressure sensor fail in my abs module. I wasn't aware at the time of services such as BBA Reman & Module Masters at the time, so I purchased a 2nd hand unit on ebay.
My original ABS module part number was 4F0614517L, as inscribed on the hydraulic unit. The part I purchased has the identical part number as well.
I changed the units out and bled the brakes, only to see a few different trouble codes appear. See here;
-------------------------------------------------------------------------------
Address 01: Engine (AUK) Labels: 06E-910-559-BKH.lbl
Part No SW: 4F1 910 559 C HW: 4F1 907 559
Component: 3.2l V6 FSI 0010
Revision: --H15--- Serial number:
Coding: 01050400190F0120
Shop #: WSC 02325 785 00200
VCID: 2B53BF628AE505461EF-807E
3 Faults Found:
18061 - Please check DTC Memory of ABS Controller
P1653 - 008 -
Freeze Frame:
Fault Status: 00101000
Fault Priority: 2
Fault Frequency: 43
Reset counter: 193
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:08:17
Freeze Frame:
RPM: 1056 /min
Mass Air / Rev.: 130.8 mg/str
Temperature: 42.0°C
Idle
Load: 16.9 %
Speed: 0.0 km/h
-------------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 4F0-910-517.lbl
Part No SW: 4F0 910 517 L HW: 4F0 614 517 L
Component: ESP 8.0 quattro H03 0090
Revision: 00000000 Serial number: 00000000000000
Coding: 0020875
Shop #: WSC 02327 785 00200
VCID: 2D57B17AB4F10B7600B-8078
5 Faults Found:
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 39
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:42:56
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x47A2
Hex Value: 0x001E
Hex Value: 0x3EAC
Hex Value: 0x00FF
01321 - Control Module for Airbags (J234)
000 - -
Freeze Frame:
Fault Status: 11100000
Fault Priority: 1
Fault Frequency: 38
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:34
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x309C
Hex Value: 0x00FF
01314 - Engine Control Module
000 - -
Freeze Frame:
Fault Status: 11100000
Fault Priority: 1
Fault Frequency: 38
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:35
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x319C
Hex Value: 0x00FF
18055 - Check Coding of ECUs on Powertrain Data Bus
P1647 - 000 -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 37
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:45:35
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x4782
Hex Value: 0x0014
Hex Value: 0x209C
Hex Value: 0x00FF
01486 - System Function Test Activated
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 3
Fault Frequency: 36
Reset counter: 207
Mileage: 137799 km
Time Indication: 0
Date: 2014.10.18
Time: 17:49:54
Freeze Frame:
Hex Value: 0x00C0
Hex Value: 0x47A2
Hex Value: 0x0021
Hex Value: 0x4194
Hex Value: 0x00FF
-------------------------------------------------------------------------------
The G201 Brake Pressure sensor error has gone, and my cruise control works again - so im inclined to think that the module/pump i fitted works. Now when I start up the vehicle I get 3 loud beeps for brakes - and the lights continually flash when driving.
I have managed to clear the steering angle fault (00778), and the System Function Test (01486)
I cannot clear 18055, 01314, and 01321.
Anyone with any assistance or information on how to do this would be greatly appreciated.
I have mailed the full autoscan to Ross-Tech but I didnt receive any feedback from them - I do own a genuine vag-com hex-can-usb cable purchased from hexdiagnostics south africa. So I am a bit stuck for help.
