Recent content by lukappaseidue

Selezionare 5f informazioni centralina elettronica > Abilita Byte 24 Bit 1 - Controllo funzione di codifica unità 5f 07 Poi eseguire un reset MMI. Select 5f electronic control unit information > Enable Byte 24 Bit 1 - Control unit 5f encoding function 07

OK. Tested but with no luck. Just the time to insert the long coding number and VCDS (14.10.0) shows "Coding rejected - Error 31: Request out of range" I own an A3 8VA Sportback 5 doors, 1.6 TDi with hold assist Sat/nav Basic Standard no touch or plus

The source from wich I've found the tip is for general purpose (I write you PM) So I don't know. One silly question: what happen if i write directly the long coding instead tick or untick byte? Can I switch back if something goes wrong (I've fear of "0" masked byte) Anyway it seems the tip is ok

happy to "see" you veeight. One question: adaptation are the same, but it seems that STG3 coding is different: it seem that last long coding number are different (the one from german forum are: 30C202, while the one from you is 388608) which is the right one?

not tested yet: I found the coding in a famous germn forum where it seem working fine It is my mistake: I have not tested yet the coding but it seem that is working I don't know if I can write link to another german MOTOR TALKing forum

ENABLING TPMS (I've tested yet) English STG03 -> Coding -> Last 6 digits change in the following values: 30C202 STG5F -> Personalization -> (13) - Vehicle Feature List BAP tire_pressure_system_0x07 -> Active STG5F -> Personalization -> (14) - Vehicle Feature List BAB...

No solution yet? Please help me

sorry for my short post this coding seems to unlock/activate SDS on A3 Cabrio go to 5F module and look for byte 18: 1. Byte 18 - Bit 2 -> From 0 to 1 2. Byte 24 - Bit 1 -> From 0 to 1 3. Byte 18 - Bit 2 -> From 1 to 0 MMI reset It should go. try and tell me if it is ok for you.

Coding: Byte 18 Bit 2 a 1 valore Byte 24 Bitt 1 al valore 1 poi Byte 18 Bit 2 di nuovo impostato al valore 0 MMI reset

I wrote you a PM some days ago- Why you donìt reply me. I hope the we could find a solution, togheter

hi Phil1824, I perhaps found the way to activate SDS, but I need you help. For confirmation I need your AUTOSCAN.TXT and admaplogs.CSV of 9,16,17,19 and 5F modules You can sent them at: lukappaseidue@gmail.com Meanwhile You can try this: Module "steering wheel electronics (16)" "Byte 0"...

Can I Activate on my A3 8VA 1.6 TDi SportBack with MMI no touch or plus?

EDIT: yesterday I left my car with SDS coded, but no MMI menu. This morning, when switching on the car, the MMI SDS menu was there !!! and it was ok (i speak and car listen my commadn) until stopped car for mor than 10 minutes!!! PLease, help

I've installed, aftermarket by AUDI original spare part (retrofit) steering wheel command; but at authorized AUDI workshop was not able to activate voice command. This is the question: I'd Like to know if Can I activate VOICE command onto my AUDI A3 8V (sportback edition) SportBack 1.6 that...

My A3 Sportback is born without steering wheel command and voice command too. So I bought retrofit kit to have them, but I was no able to activate SDS (I've been able, but coding is lost turning of the car) So, I'm waiting that someone is able to activate SDS like cabrio version