Recent content by HOTTIGGER

hi all, I need the part number for the gasket that goes on the haldex pre charge pump, I'm changing my haldex pump Saturday and I want to put a new gasket on where it joins the rear diff, thanks in advance, p.s my s3 is a pre face lift 210bhp. Thanks again.

hi m8, my controller is fine i think, its the pump im changing, mine is a 210bhp and the pumps of a 225bhp, the look the same but id like to be sure before buting it. thanks.

hi tuffy thanks for repaly, yes mine is an early s3 with no earth strap on the rear/axel, my hardex controller is working ok i hope, and i dint plan on touching it if i dint have to, the pump ive seen is of a 225bhp and looks the excat same, but u carnt be sure with these s3, as every part i buy...

hi all, is the haldex pump the same of a 225bhp as a 210bhp ?? ive got a 1999 s3 210bhp with a nackered haldex pump, ive bin offered a pump of a 225bhp, it looks the same but i want to be sure before buying it,. thanks in advance .

hi all ive got a 1999 s3, i think the drive shafts and hubs have bin updated to audi tt or something, this is the number of the shaft 8n0413031g, its got a bolt in the centre of the cv joint, not like the s3 thats got a nut, i beleve these shafts are off a 2001 model, could some1 please tell...

hi all, ive got a 1999 audi s3 and i think my drive shafts and hubs have bin changed, i orded this cv joint AUDI S3 QUATTRO 1.8 TURBO CV JOINT & BOOT KIT (BRAND NEW) 99>01 | eBay, when i phoned up and told them mine was held in by a bolt like this one AUDI S3 QUATTRO 1.8Turbo DRIVESHAFT CV...

hi all i need to bleed the clutch on a s3, i hade the brake master cylinder changed a few week ago but i dont think the clutch was bleed propley as the gears seem to be crunchy, i dont want to bleed the brakes again just the clutch, can i do this on my owne with an ezzbleed ? do i just connect...

Hi m8 thanks for reaply, yes it a proper Ross tech cable not lite or copy cable, how do I change it back to mph? Thanks, QUOTE=gen.heinz guderian;1674017]If you have licensed cable it can change it.. Not sure about lite or copies.

hi all, my m8 has a 2003 mk4 golf, while messing with a memoscan 5053 he some how changed the mph to kph, and can not change it back to mph, can I change it back with my vcds cable ?, if so how do I do it ? please help thanks in advanced.

hi all, can i check my abs is working with vcds? i dont want to bleed the brakes, just test the abs is working, ive all ready done a scan and no fault with abs, i changed the m/c last week and brakes are fine but not sure if the abs is cutting in as i nearly skided today when stoping quick, can...

HI m8 thanks for reaply, I've just tryed it on loose gravel and the back wheels locked up, so my abs in not working ?, does it just need reset or something ?, thanks in advance . UOTE=<tuffty/>;1668605]If it nearly locked up then its most likely working... Try braking on a looser surface at...

hi all, i hade my master cylinder changed last week at a grarge, the brakes are loads better, but today i needed to stop quite quick and slammed on the brakes, i dont think the abs cut in as my front wheel nearly locked up, and i dint fell any push back of the peddel, ive scaned with vagcom no...

hi all im going to use vcds to try bleed my brakes, i can not bleed the m/c because 1 of the nipples is broken off, i changed a caliper and lost loads off fluid, and now after a power bleed the pedal is still spongy, i know it can be bleed like this as a garage did it with vcds a few months ago...

have u read the thread m8? i carnt bleed manualy, 1 of the nipples is broke off the m/c. thanks

I carn't do the manual method, 1 of the nipples is broken off the m/c, its bin done b4 so can defo be done , I just wanted a but off help with it ,as I'm not used to using vcds, thanks,