Retrofit automatic height adjustment for Bi-xenons

[Chielvb]

Ok, checked all the wiring, is correct now.

I got Dipped beam, high beam, DRL, etc working.
But not the AFS.

There seems to be a problem when I want to recode the module 55 xenon range.

I get unknown fault 78.

The number for the module is 4F0 910 357 F
This seems a A6 number to me?!?!?

Anyone??

 

[NHN]

So the wiring was incorrect afterall, tut tut, lol

Has the module been initialised on the car, in other words has it got an importer & workshop code in 55 or is it just zero's at the top?

Can you show me a screen dump of the coding screen of 55 & also the error, are you getting any no subsystem errors?

I assume you disconnected the old manual height adjustment wiring?

 

[Chielvb]

Has the module been initialised on the car, in other words has it got an importer & workshop code in 55 or is it just zero's at the top?

It has an importer and workshop code, I recoded Canbus to recognise it.

Can you show me a screen dump of the coding screen of 55 & also the error, are you getting any no subsystem errors?

Will give it a shot

I assume you disconnected the old manual height adjustment wiring?

Yes they are disconnected

I think the xenon range module is the problem, I'm going to try Kufatec to send me an other one.

 

[NHN]

Updates on this mate?

 

[Chielvb]

Yes, I'm again working on it.

Now I have replaced the xenon modules at the headlights for the ones with an A at the end. This solves almost all the problems. I can recode them, only one fault, that is: Headlights not adjusted.

But when I try to adjust them it takes minutes and nothing happens, I think because of Group 002 which says sensors undefined.

Maybe because the car is lowered?!?! But when I first installed the kit, I had a normal value at Group 002. Lowering has been done before I installed the leveling kit.

Anyone??

Log:

Friday,31,July,2009,17:13:13:09292
VCDS Version: Release 805.3
Data version: 20090213

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------

Address 55: Xenon Range (4F0 910 357 F)
17:13:06 Group 001
13.9 V Voltage (Terminal 15)
0.02 s Time Constant
0.00 m/s^2 Vehicle Acceleration
0.0 (no units)
17:13:06 Group 002: Sensors
Undefined Front Sensor Signal
Undefined Rear Sensor Signal
5.0 V PWM Sensors Voltage Supply
N/A
17:13:06 Group 011: Sensor Values
19.9 % Front Sensor Value
71.7 % Rear Sensor Value
N/A
N/A

 

[Chielvb]

OK, they are working just fine now.

Set factory settings to default. And everything works.

NHN thanks for your great help

 

[NHN]

Hey no worries, not sure if I helped that much, what did you actually do in the end so others can benefit from the info.

Glad all works though, they're cool huh, great mod if done 10 properly.

My next challenge is fitting the hybrid turbo as mine blew up, joy but learning aswell.

 

[Khufu]

My next challenge is fitting the hybrid turbo as mine blew up, joy but learning aswell.

 

[NHN]

Its arrived today, so wish me luck as got to remove front of car to take out intercooler to flush it from the oil spilled into system from turbo going pop, joyyyyy, not at all.

 

[Finder]

** decided it's better to open a separate thread **
http://www.audi-sport.net/vb/a3-s3-sportback-8p-chassis/204640-afs-bi-xenon-retrofit.html