Multi function steering wheel

Boon

Boon

Registered User
Joined
Sep 22, 2012
Messages
441
Reaction score
59
Points
28
Location
South East Kent
Would anyone know if a direct replacement, what extra parts need to replace my wheel

my current p/n 8P0 419 091

change to 8T0 419 091

I have vag-com to enable the multifunction but will it require any wireing or modules?

thanks
 
A3 sportback 2.0TDI 54 plate

Steering wheel controller 1K0 593 549 A
Current soft coding 0000012

Thanks
 
You need a Highline DIS ( split into 3 sections ), a steering controller 8P0 953 549 F and slip ring suffix 'D'. for the mfsw to work.

You will also need to ensure that your existing airbag fits the new wheel and that your car is already fitted with a two stage airbag system.
 
Hi Guys,
I dont want to start another MFSW thread.

My car is 2008 S3 Sportback facelift car and i had S3 steering wheel no multifunction. I wanted to have RS steering wheel so i bought new one with 8J0 419 091 code - pls see picture. I also bought used airbag but i dont have part# - the guy asked me for my steering wheel picture and number and he said this airbag should be good.

From what i've read i need 8P0971589Q cabling to connect steering wheel and airbag and then i need 1K0959653D clockspring and also new module 8P0 953 549 F, as according to VAG software i have 1k0 953 549 AH.

Can you please confirm that i need to purchase all 3 above items to get it working for my S3?

Currently i lost steering assistant and driving is very difficult and ESP airbag faults.

Much appreciated for your help!!!

471aacef5be3f.jpg


07f92fc2db9a7.jpg
 
You will need the cable you mention although the part # with suffix 'Q' may now be superseded. Audi will give you the correct one for mfsw.

You will need the steering module you mention --- 8P0 suffix 'F

I think you will already have the correct slip ring (suffix D) because that was usually fitted with the steering module that you already have.

After installation you will need to carry out steering basic settings and code the wheel with VCDS to get steering assist back and then all lights will extinguish.

Just be sure that the 'used' airbag has not been deployed and is still intact. If you paid less than about £150 - £200 for it then it is likely to be 'dodgy'.
 
Hi Mike,

Airbag is intact and was never fired up - im pretty sure it works correctly,just hope it will work with all electronics. Unfortuantely my steering sensor might been damaged as i havent replaced it or secured it after i changed the steering wheel. We also tried diagnostics with VCDS and when i moved the steering right / left the sensor didnt show any movement and that might be the cause why i lost steering assistant. I guess i'll get all three items and i should be able to conenct everything and get everything working.

Is there a chance that my steering angle sensor is still working or its already damaged?


thanks!
 
Hi fella, I have a steering angle sensor if interested. Can sell for £15 posted.

PM me if interested. I also have a slip ring available.
 
It's unlikely to be damaged. The slip ring and steering angle sensor are in the same unit but you need to carry out the basic settings with VCDS to get it to work.

check the RossTech site for instructions.
 
If you can post a copy if your scan, then we can see the fault codes and point you in the right direction.
It is most likely what Mike has said, and probably needs basic settings and adaptation preformed.
 
My logs below:


Address 03: ABS Brakes (-----) Labels: 1K0-907-379-60EC1F.clb
Part No SW: 1K0 907 379 AE HW: 1K0 907 379 AE
Component: ESP MK60EC1 H35 0104
Revision: 00H35001
Coding: 14428012092600FC281401ED901D00413800
Shop #: WSC 06314 000 00000
VCID: 75E5E5E760E5


3 Faults Found:
01826 - Sensor for Steering Angle (G85); Supply Voltage Terminal 30
000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 2
Fault Frequency: 1
Reset counter: 50
Mileage: 74691 km
Time Indication: 0
Date: 2012.10.01
Time: 07:50:54


Freeze Frame:
Count: 2
Count: 2
Count: 12800
Count: 294
Count: 42496
Count: 0
Count: 0
Count: 0


01314 - Engine Control Module
013 - Check DTC Memory - Intermittent
Freeze Frame:
Fault Status: 00101101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 51
Mileage: 74699 km
Time Indication: 0
Date: 2012.10.01
Time: 08:05:25


Freeze Frame:
Count: 2
Count: 32768
Count: 12800
Count: 8193
Count: 49722
Count: 0
Count: 0
Count: 0


00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 5
Reset counter: 11
Mileage: 74666 km
Time Indication: 0
Date: 2012.09.30
Time: 06:26:27


Freeze Frame:
Count: 3
Count: 2
Count: 12800
Count: 295
Count: 45312
Count: 57856
Count: 0
Count: 0
Click to expand...


oraz


Address 44: Steering Assist Labels: 1Kx-909-14x.lbl
Part No: 1K0 909 144 C
Component: EPS_ZFLS Kl. 234 2301
Revision: 00H15000
Shop #: WSC 02069 000 90108
VCID: 2A5F069BF9DB


3 Faults Found:
16353 - Control Module - Internal Malfunction
014 - Defective - MIL ON
Freeze Frame:
Fault Status: 11101110
Fault Priority: 6
Fault Frequency: 1
Reset counter: 2
Mileage: 74323 km
Time Indication: 0
Date: 2012.06.09
Time: 01:39:15


Freeze Frame:
Battery Volts: 11.7 V
DU
Temperature: 27.0∞C
Error Code: 14745
Torque: -6.8 Nm
Torque: -2.304 Nm
RPM: -2388 /min


00573 - Steering Torque Sensor (G269)
004 - No Signal/Communication - MIL ON
Freeze Frame:
Fault Status: 11100100
Fault Priority: 6
Fault Frequency: 3
Reset counter: 10
Mileage: 74700 km
Time Indication: 0
Date: 2012.10.01
Time: 08:08:01


Freeze Frame:
Battery Volts: 12.2 V
DU
Temperature: 34.0∞C
(no units): 65
(no units): 32
Torque: 0.0 Nm
Count: 837


02391 - Terminal 30 Reference
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 3
Fault Frequency: 1
Time Indication: 0


Freeze Frame:
Voltage: 12.88 V
PD
Temperature: 34.0∞C
Speed: 50.0 km/h
Torque: 0.0 Nm
Torque: 0.000 Nm
Term 15 On
Click to expand...
 
On this subject, mines has a mode button and a button with arrow pointing left, when I push either it says...no function

What are these for?
 
Cossie_boy said:
On this subject, mines has a mode button and a button with arrow pointing left, when I push either it says...no function

What are these for?
Click to expand...

The arrow button only works with Audi Bluetooth phone connection installed. The mode button only works with RNSE installed as far as I know !
 
Mines an 08 so guessing it doesnt have that then, are those boxes plug and play?!
 
Mario, silly question but have you tried to clear these faults?

Anyhow, if you check all the links i have provided from Ross Tech, they give possible causes and solutions to your fault codes.

Address 03: ABS Brakes
Fault code 01826 01826 - Ross-Tech Wiki
Fault code 01314 01314 - Ross-Tech Wiki
Fault code 00778 00778 - Ross-Tech Wiki

Address 44: Steering Assist
Fault code 16353 Can't seem to find a fault code related to this on Ross Tech
Fault code 00573 00573 - Ross-Tech Wiki
Fault code 02391 Can't seem to find a fault code related to this on Ross Tech


This is the best i could at the moment mate, see how you get on with the possible solutions in the links.
 
mike foster said:
The arrow button only works with Audi Bluetooth phone connection installed. The mode button only works with RNSE installed as far as I know !
Click to expand...

You are half right Mike.
The arrow button is used for voice control used with oem bluetooth and also SDS versions of the RNS-e.
The Mode button is used to switch between your phone book and radio on you DIS, which works with RNS-e, Chorus, Symthony etc, but you still need to have the bluetooth installed for this to work.
Without bluetooth, then these are just dead buttons.
 
Thanks Danny - it's a long time since I researched the subject and, as I do not have rnse installed, the detail had faded somewhat !!!
 
mike foster said:
Thanks Danny - it's a long time since I researched the subject and, as I do not have rnse installed, the detail had faded somewhat !!!
Click to expand...

No problem Mike. But you more than make up for with all the time and effort you put into this site to help others. Your a credit to this site mate, and many will agree.
 
New wheel fits... Airbag fits new wheel, has two wires, so two stage I guess?!...

how can I tell if I have a 'Highline' DIS?

Then just need the module and slip ring..... Also a new cable to connect slip ring to the wheel controls/airbag?
 
Boon said:
New wheel fits... Airbag fits new wheel, has two wires, so two stage I guess?!...

how can I tell if I have a 'Highline' DIS?

Then just need the module and slip ring..... Also a new cable to connect slip ring to the wheel controls/airbag?
Click to expand...

you already have the dual stage airbag system being a sportback.
Also no need for a new slip ring as your current one will be fine. Yes, all you need now is the wiring loom, the correct steering module (8p0 953 549 F) and a bit of VCDS coding.

Out of interest, have you physically checked the airbag fits? Because the part numbers you provided in your OP suggests that your current airbag will not fit the 8T0 wheel as they are different fitments.
 
Last edited:
Dannykn9 said:
you already have the dual stage airbag system being a sportback.
Also no need for a new slip ring as your current one will be fine. Yes, all you need now is the wiring loom, the correct steering module (8p0 953 549 F) and a bit of VCDS coding.

Out of interest, have you physically checked the airbag fits? Because the part numbers you provided in your OP suggests that your current airbag will not fit the 8T0 wheel as they are different fitments.
Click to expand...

Great, many thanks.

I took a chance that even if it wouldn't work I'd have a new wheel to use or sell!

Yes the airbag fits... New wheel and original airbag have been fitted to car for a few weeks now, just want the controls to light up and use the volume as the RNS-E volume knob needs a clean inside (volume often goes up when turning down!)

On the lookout for a module now then :)
 
Would anyone know if steering control module 1K0 953 549 F will work or do I need 8P0 953 549 F?

Is there any difference?
 
MFSW only works with the 8P0 module!
I may have one for sale.. just waiting to hear from the customer who wanted it... if he doesnt get back to me then its going to go back for sale
 
Ok so

Steering module 8P0 593 549 fitted and new harness 8P0 971 589 AD

The buttons dont do what they are ment to... They light up... But...

The left wheel when pressed in turns up the volume... The right wheel when pressed turns down the volume...

The Mode & Voice buttons turn the tracks!

Had noticed that the wires do not match up...

Wheel end Pin 1 - Black, Pin 2 - Yellow, Pin 3 - Red
Harness Pin 1 - Blue, Pin 2 - Red, Pin 3 - Black

I tried repinning to match Black to Black, Red to Red & Blue to Yellow but nothing worked at all

Is there a way to repin or recode something so they work as they should?
 
You must log in or register to reply here.

Similar threads

Lee1991
Multi Function steering wheel help ...
Replies
2
Views
843
Donny_DJ
Donny_DJ
Z
Multi-function Steering Wheel Retrofit
Replies
0
Views
1K
ZeeSaffa
Z
ckh
Normal Steering wheel to Multi Function Steering wheel
Replies
10
Views
2K
MikeSel^
MikeSel^
T
Retro fit multi function steering wheel
Replies
17
Views
2K
Ash187
Ash187
Von Maximo
Retro Fitting Multi Function Steering Wheel?
Replies
1
Views
1K
JamS3
JamS3
Top
Back