Fault codes on New K Module ..Help ?

[Khufu]

Yes, O/S rear is correct side for fog light in UK, a German version off ebay.de will be on the N/S as they drive on the right hand side of the road. Is the CE module coded for UK? Isnt there an option for that? Will check when laptop is charged enough LOL

 

[a8 tech back]

may be of some use en.openobd.org - audi - a3 (8p)

 

[Khufu]

Audi Portal: ECU Diagnostic

 

[a8 tech back]

show a dump of byte 4
Byte 04 Bit 4 Activation of both Rear Fog Lights
Byte 04 Bit 5 Model (0 = Right Hand Drive / 1 = Left Hand Drive)
Byte 04 Bit 6 Rear Fog Lights deactivated


byte 4 looks correct from the earlier long code but just check it and recheck byte 03 as well and change for one fog one reverse

 

[J.R.]

Here is the list of the label files :


;
; VCDS Label File
;
; Copyright © 2006-2009 Ross-Tech, LLC
;
; Audi A3 (8P) / Audi R8 (42) / Audi TT (8J)
;
; Component: J519 - Central Electronics I (#09) - HIGHEND (30 Byte)
;
; P/N: 8P0-907-279-???
;
; includes measuring blocks, adaptation, selective output test and long coding
;
; This file is part of a redirection package,
; make sure you have all of the following files.
;
; 8P-09.LBL
; 8P0-907-279-23-H.LBL
; 8P0-907-279-30-H.LBL
;
; created on 18/Jul/2006 by Sebastian Stange (Sebastian@Ross-Tech.com)
;
; last modificationon on 24/Jan/2009
;
; requires VCDS 805.0 / LCode 804.0 or newer
;
;
;---------------------------------------------------
;
; measuring blocks
;
;---------------------------------------------------
;
;
001,0,Parking Lights
001,1,Left Front,Parking Light,Range: 0.0...100.0 %
001,2,Right Front,Parking Light,Range: 0.0...100.0 %
001,3,Left Rear,Parking Light,Range: 0.0...100.0 %
001,4,Right Rear,Parking Light,Range: 0.0...100.0 %
;
002,0,Fog Lights/Low Beams
002,1,Left Low Beam,Headlight,Range: 0.0...100.0 %
002,2,Right Low Beam,Headlight,Range: 0.0...100.0 %
002,3,Left Fog Light,,Range: 0.0...100.0 %
002,4,Right Fog Light,,Range: 0.0...100.0 %
;
003,0,Turn Signals
003,1,Left Front,Turn Signal,Range: 0.0...100.0 %
003,2,Right Front,Turn Signal,Range: 0.0...100.0 %
003,3,Left Rear,Turn Signal,Range: 0.0...100.0 %
003,4,Right Rear,Turn Signal,Range: 0.0...100.0 %
;
004,1,Left Side,Turn Signal,Range: 0.0...100.0 %
004,2,Right Side,Turn Signal,Range: 0.0...100.0 %
004,3,Left/Right,High Beam,Range: 0.0...100.0 %
004,4,Xenon-Shutter,,Range: ON/OFF
;
005,0,Brake Lights
005,1,Left,Brake Light,Range: 0.0...100.0 %
005,2,Right,Brake Light,Range: 0.0...100.0 %
005,3,Center,Brake Light,Range: 0.0...100.0 %
005,4,License Plate,Illumination,Range: 0.0...100.0 %
;
006,0,Back-Up Lights
006,1,Instrument,Illumination,Terminal 58d (Range: 0.0...100.0 %)
006,2,Left,Back-Up Light,Range: 0.0...100.0 %
006,3,Right,Back-Up Light,Range: 0.0...100.0 %
006,4,Left Rear,Fog Light,Range: 0.0...100.0 %
;
007,1,Activation Relay,Terminal 50,Range: ON/OFF
007,2,Activation Relay,Terminal 15,cockpit/engine (Range: ON/OFF)
007,3,Activation Relay,Terminal 75,Range: ON/OFF
007,4,Enabling SAD,,Range: active/inactive
;
008,1,Brightness,,Range: 0...7
008,2,Rain Quantity,,Range: 0...7
008,3,Right Rear,Fog Light,Range: 0.0...100.0 %
008,4,Footwell,Lighting,Range: 0.0...100.0 %
;
009,1,Terminal 30g,Relay,Range: ON/OFF
009,2,Dual Washer,Pump +,Range: ON/OFF
009,3,Dual Washer,Pump -,Range: ON/OFF
009,4,Heated Rear,Windshield,Range: ON/OFF
;
010,1,Horn,,Range: Operated/Not Oper.
010,2,Enabling of,Seat Heating,Range: Active/Inactive
010,3,Electric Fuel,Pump (FP) Relay,Range: ON/OFF
010,4,Headlight Washer,System Relay,Range: ON/OFF
;
011,1,LED Heated Rear,Windshield,Range: ON/OFF
011,2,LED Emergency,Flasher Button,Range: 0.0...100.0 %
011,3,LED Heated,Outside Mirror,Range: ON/OFF
011,4,Interior,Light Dimmed,Range: 0.0...100.0 %
;
012,1,Coming Home,LED,Range: ON/OFF
012,2,Heated Outside,Mirror,Range: ON/OFF
;
013,0,Terminals
013,1,Terminal 30,(left),Range: 0.00...17.75 V\nSpecification: 5.0...17.75 V
013,2,Terminal 30,(right),Range: 0.00...17.75 V\nSpecification: 5.0...17.75 V
013,3,Terminal 30,(ref.),Range: 0.00...17.75 V\nSpecification: 5.0...17.75 V
013,4,Terminal 31,(ref.),Range: 0.00...12.75 V\nSpecification: 0.0...1.00 V
;
014,1,Dimming,Potentiometer,Range: 0.0...100.0 %
014,2,Coming Home,,Range: 0.0...100.0 %/ON/OFF
014,4,HomeLink,,Range: Operated/Not Oper.
;
015,0,Terminals
015,1,Terminal 15,(Input),Range: ON/OFF
015,2,Terminal 50,(Input),Range: ON/OFF
015,3,Enabling P/N,,Range: ON/OFF
015,4,Terminal L,(Input),Range: ON/OFF
;
016,1,Brightness,,OFF = Bright\nON = Dark
016,2,Lights on (RLS),,Range: ON/OFF
016,3,Front Wiper,Status,Range: ON/OFF
016,4,Wiper turn-around,Position Signal,Range: Reached/Not Active
;
017,1,Light Switch,(Light off),Range: ON/OFF
017,2,Parking Light,Switch,Range: ON/OFF
017,3,Low Beam,Headlight Switch,Range: ON/OFF
017,4,AFL Light Switch,,Range: ON/OFF
;
018,1,Fog Light Switch,,Range: ON/OFF
018,2,Light Switch,Rear Fog Light,Range: ON/OFF
018,3,Brake Light Switch,,Range: ON/OFF
018,4,Back-Up,Light Switch,Range: ON/OFF
;
019,1,Emergency,Flasher Button,Range: Operated/Not Oper.
019,2,Engine Hood,,Range: Open/Closed
019,3,Heated Rear,Windshield Button,Range: Operated/Not Oper.
019,4,Heated Outside,Mirror,Range: Operated/Not Oper.
;
020,0,Backrest Recognition
020,3,Backrest,Left,Range: ON/OFF
020,4,Backrest,Right,Range: ON/OFF
;
021,0,Rotary Traps
021,1,Rotary Trap LF,,Range: ON/OFF
021,2,Rotary Trap RF,,Range: ON/OFF
021,3,Rotary Trap LR,,Range: ON/OFF
021,4,Rotary Trap RR,,Range: ON/OFF
;
022,1,Rear Lid,Main Catch,Range: ON/OFF
022,2,Heated Front,Windshield,Range: operated/n. oprated
022,3,Heated Front,Windshield Relay,Range: ON/OFF
022,4,Heated Front,Windshield LED,Range: ON/OFF
;
023,1,Rotary Light Switch,Position
023,2,Coming Home,Condition
023,3,Leaving Home,Condition
023,4,AFL Condition
;
024,1,Steering Column,Switch Information,via LIN-Databus
024,2,Terminal 15,(via LIN),Range: ON/OFF
024,3,Terminal 50,(via LIN),Range: ON/OFF
024,4,Wiper Cycle,Number (via LIN)
;
030,1,Load Management,,Range: Active/Inactive
030,2,Short-Distance,Operations
030,3,Critical,Time Fraction
;
080,0,Advanced Control Module Identification I
;
081,0,Advanced Control Module Identification II
;
082,0,Advanced Control Module Identification III
;
;
;---------------------------------------------------
;
; adaptation
;
;---------------------------------------------------
;
;
A000,0,Reset Adaptation Channels
A000,5,Reset Adaptation Channels
A000,6,Reset all adaptation channels back
A000,7,to the original factory values.
;
A001,0,Coming-Home Time
A001,5,Coming-Home Time
A001,6,Time which the Coming-Home function will be active.
A001,7,Range: 10...60 Seconds
A001,8,Resolution: 10 Seconds
A001,9,Note: Only active if Byte 00 Bit 7 of Long Coding active.
;
A002,0,Leaving-Home Time
A002,5,Leaving-Home Time
A002,6,Time which the Leaving-Home function will be active.
A002,7,Range: 10...60 Seconds
A002,8,Resolution: 10 Seconds
A002,9,Note: Only active if Byte 00 Bit 5 of Long Coding active.
;
A003,0,Rear Window & Outside Mirror Heater Activation Time
A003,5,Rear Window & Outside Mirror Heater Activation Time
A003,6,Time which the Rear Window and Outside Mirror Heater will be active.
A003,7,Range: 1...254 Minutes
A003,8,Resolution: 1 Minute
;
A004,0,Headlight Washer Activation Time
A004,5,Headlight Washer Activation Time
A004,6,Range: 50...10000 ms
A004,7,Resolution: 50 ms (Adaptation Value * Resolution = Actual Value)
A004,8,Note: Only active if Byte 01 Bit 1 of Long Coding active.
;
A005,0,Footwell Lighting Dimming
A005,5,Footwell Lighting Dimming
A005,6,Range: 20...100 %
A005,7,Resolution: 1 %
A005,8,Note: Only active if Byte 00 Bit 1 of Long Coding active.
;
A006,0,Load Management
A006,5,Load Management
A006,6,Range: 0...3
A006,7,Note: Only active if Byte 02 Bit 3 of Long Coding active.
;
A007,0,Highbeam with Assistance Driving Light
A007,5,Highbeam with Assistance Driving Light
A007,6,0 = inactive
A007,7,1 = active
;
A008,0,Assistance Driving Light Activation/Deactivation Delay
A008,5,Assistance Driving Light Activation/Deactivation Delay
A008,6,Range: 0...10200 ms
A008,7,Resolution: 40 ms
;
;
;---------------------------------------------------
;
; selective output test
;
;---------------------------------------------------
;
;
T59,Interior Lighting
T60,Foglight Lamps
T156,Front Windshield Washer Pump
T901,Back-Up Lamps
T906,Horn (H1)
T909,Windshield Wiper Motor (V)
T967,Left Turn Signals
T968,Right Turn Signals
T975,Heated Rear Window (Z1)
T977,Low Beam (Left & Right)
T2486,High Beam (Left & Right)
T1064,Interior Dimming (Terminal 58d)
T1259,Fuel Pump Relay (J17)
T1504,License-Plate Light (X)
T1701,Dimmer for Interior Lighting
T1755,Parking Lights (E1)
T1758,Brake Lamps
T1830,Rear Fog Light(s)
T2377,Wiper: Upper Reverse Point
T2398,Rear Windshield Washer Pump
;
;
;---------------------------------------------------
;
; long coding
;
;---------------------------------------------------
;
;
LC,00,0,Front Fog Lights installed
LC,00,1,Xenon Headlights with Shutter installed
LC,00,2,Footwell Lights installed
LC,00,3,Daytime Running Lights (Scandinavia) active
LC,00,4,Daytime Running Lights (North America)
LC,00,5,Assistance Driving Light & Leaving Home active
LC,00,6,Rain-/Light sensor installed
LC,00,7,Coming-Home active
LC,01,0,Rear Seat Recognition installed
LC,01,1,Headlight Washer installed
LC,01,2,Electronic Fuelpump Relay installed (Gasoline only)
LC,01,3,Rear Wiper installed
LC,01,7,Rear Wiper with Front Wiper continiously active
LC,02,0,Rear Wiper with Front Wiper intermittent active
LC,02,1,Comfort Turn Signals
LC,02,2,Cold Lamp Diagnosis active
LC,02,3,Load Management active
LC,02,4,Coming-Home Mode via (0 = Personalisation / 1 = Lightsensor)
LC,02,6,Side Turn Signal Lights installed
LC,02,7,Seat Heating installed
LC,03,0,Relay Terminal 15 installed
LC,03,1,Rear Fog Lights (0 = 2 Rear Fog Lights / 1 = 1 Rear Fog Light)
LC,03,2,Reverse Driving Lights (0 = 2 Reverse Driving Lights / 1 = 1 Reverse Driving Light)
LC,03,3,Reverse Driving Light off when Rear Lid open
LC,03,4,Xenon-Shutter without Shutter installed (Bi-Xenon)
LC,03,5,Teardrop Wiping for Rear Window active
LC,03,7,Rear Lights (1 = Back Light/Brake Light dimmed / 0 = Back Light dimmed)
LC,04,0,Auxiliary Heater installed
LC,04,1,Auxiliary Heating installed
LC,04,2,Trailer/Towing Device installed
LC,04,3,Memory Seats installed
LC,04,4,Activation of both Rear Fog Lights
LC,04,5,Model (0 = Left-Hand-Drive / 1 = Right-Hand-Drive)
LC,04,6,Rear Fog Lights deactivated
LC,04,7,Climatronic installed
LC,05,0-7,50,Headlight Washer Delay
LC,05,0-7,50,Decimal Value (Resolution 50 ms) (Example: 20 is 20 x 50 = 1000 ms)
LC,06,0-7,50,Headlight Washer Activation Time
LC,06,0-7,50,Decimal Value (Resolution 50 ms) (Example: 16 is 16 x 50 = 800 ms)
LC,07,0-7,1,Turn Signal Front left/right as Parking Light Front left/right (USA and Canada)
LC,07,0-7,1,Decimal Value (Resolution: 1%)
LC,08,0,Seat Heating Deactivation with Transport Mode active
LC,08,1,Daytime Running Light (DRL) Deactivation with Transport Mode active
LC,08,2,Footwell Lighting Deactivation with Transport Mode active
LC,08,3,Interlock Display via CAN-Instruments active
LC,08,4,Interior Light via Rear Lid Notch active
LC,08,6,Rear Fog Light Deactivation with Trailer active
LC,08,7,Daytime Running Light (DRL) Deactivation while Blinking active
LC,09,0-7,1,Rear Brake Light as Parking Light
LC,09,0-7,1,Decimal Value (Resolution: 1%)
LC,10,0-7,1,Rear Fog Light as Parking Light
LC,10,0-7,1,Decimal Value (Resolution: 1%)
LC,11,0-7,1,Front Parking Light Dimming
LC,11,0-7,1,Decimal Value (Resolution: 1%)
LC,12,0-7,1,Rear Parking Light Dimming
LC,12,0-7,1,Decimal Value (Resolution: 1%)
LC,13,0-7,1,Backup Function: Rear Side Turn Signal as Parking/Brake Light
LC,13,0-7,1,Decimal Value (Resolution: 1%)
LC,14,0-7,1,Backup Function: Front Parking Light as Side Turn Signals
LC,14,0-7,1,Decimal Value (Resolution: 1%)
LC,15,0-7,1,Backup Function: Rear Parking Light as Side Turn Signals
LC,15,0-7,1,Decimal Value (Resolution: 1%)
LC,16,0-7,1,Backup Function: Front Fog Lights as Low Beam Headlight
LC,16,0-7,1,Decimal Value (Resolution: 1%)
LC,17,0,Emergency Brake Flash Light active
LC,17,1,Deactivation of Additional High Beam with Bi-Xenon
LC,17,2,Heated Front Window installed
LC,17,3,Diagnosis Terminal 50 active
LC,17,4,Daytime Running Light via Fog Lights
LC,17,5,Front Fog Lights deactivated with High Beam
LC,17,6,Parking Light Function inactive (USA/Canada)
LC,18,0,Cold Diagnosis License Plate Lights active
LC,18,1,Cold Diagnosis Brake Lights active
LC,18,2,Cold Diagnosis Front Fog Lights active
LC,18,3,Cold Diagnosis Rear Fog Lights active
LC,18,4,Cold Diagnosis High Beam active
LC,18,5,Cold Diagnosis Turn Signals active
LC,18,6,Cold Diagnosis Back-Up Light active
LC,18,7,Cold Diagnosis Side Turn Signals active
LC,19,0,Cold Diagnosis Low Beam active
LC,19,1,Cold Diagnosis Front Parking Lights active
LC,19,2,Cold Diagnosis Rear Parking Lights active
LC,19,3,Diagnosis Rear Parking Lights active
LC,20,0-7,1,Front Fog Light Dimming (Standard 5C)
LC,20,0-7,1,Decimal Value (Resolution: 1%)
LC,21,0~2,01,Halogen Front Light
LC,21,0~2,02,Xenon Front Light with Halogen High Beam
LC,21,0~2,03,Bi-Xenon Front Light with additional High Beam
LC,21,0~2,04,Bi-Xenon Front Light without additional High Beam
LC,21,0~2,05,Bi-Xenon Front Light with separate Daytime Running Lights (DRL)
LC,21,0~2,06,Bi-Xenon Front Light with LED Daytime Running Lights (DRL)
LC,21,0~2,07,LED Front Light
LC,21,4,Rear Fog Light as Brake Light
LC,22,1,Daytime Running Lights (DRL) switchable via Menu
LC,22,4,Speed dependant Trunk Locking active
LC,22,6,Rear Parking Lights as Blinker active (North America)
LC,22,7,Diagnosis Rear Brake Lights inactive (North America)
LC,23,1,Advanced Comfort Menu active
LC,23,7,Engine Compartment Light via Right Side Blinker Output active
;

 

[J.R.]

This is the switch turned on with rear fog....as you can see the switch works...

I don't understand what you mean by doing a dump on byte 4

also I've done a screen shot of the bytes it's currently on at the moment.

Me and RS also found out what was wrong with the interior light......as it was due to a relay in the wrong position. So one solved and 2 more to go....:thumbsup:

 

[a8 tech back]

change byte 3 for one reverse and one fog

you may have to alter the bits instead of the check box

so bit 1 and bit 2 need changing to activate one rear fog and one rear reverse

remember every time you change and save with vcds you must turn the ignition off and back on the turn the fig on and see if it works

screen dump mark 5 golf

golf 09 by a8 tech, on Flickr

osr fog nsr reverse

SO SET BIT CODE 00000110

did you move the relay position 8 to the 30 supply position 9

you are missing a 15 supply relay from position 1

if you do not need the 15 relay uncheck the box in byte 3 and try that

looking back at your old relay positions

http://www.audi-sport.net/vb/new-a3...380-central-electrics-module-relays-help.html

move the relay 460 to position 1 of the new relay carrier but I would think you need both relays

anyway try some of this lot

found the long code helper/simulator

go to c drive find ross tech and open it

scroll down till you find Lcode exe

open it and all your long code files will be there

you can now simulate code changes without being connected to the car

 

[J.R.]

I've Just coded it to exactly what you stated below..and unchecked relay 15...Still no change..

My bit code is now : 00000110

Yes... I moved the relay position 8 to the 30 supply position 9 ....And the interior lights started to work..

I tried to move relay 460 to position 1 of the new relay carrier but it was too hard to take out so I left it in there.....But I was looking at the back position of where the 460 relay slots into on the left..side of the module..and there is no current connector with wires going out in place...but on the right side where the other 460 relay is there is a connector with wires going out.

I was wondering if there would be a point of getting another 460 relay and slotting it in as there is no connectors going out the back of it.

 

[a8 tech back]

God knows whats going on with this.All I can say if your mate has done the same upgrade and the cars are the same year and spec then compare the coding and the check if the relay 460 is fitted.
Its hard to work out what should be doing what without having the car in front of me to check the wiring.
Iam sure if I had the car I would sort it out.

Stick a new scan of the faults up and post your exact vehicle details ie 8p 3 door low line none auto lights engine code etc

I have fitted a k before without any problems for xenon upgrade but cant find the vcds log

We need to see address 09 long code for other 3 door vehicles with K fitted and nsr reverse osr fog

Just wondering if there is some difference with the rear light units or light switch as output test with vcds shows the osr fog works but does it out the nsr reverse on as well

It something simple that's causing it

So presently if you select reverse or turn on the rear fogs nothing happens.

I would stick a multimeter in the pins and select output test for fog light and see which pin becomes active when it works and then post it up so we can trace the wiring back to j519

When you checked measured value blocks it shows the fog light on

Other things to mess with, try coding for both rear fogs or select the BACK TO STANDARD BUTTON in long coding and see what happens

 

[J.R.]

The Relay 460 is fitted in RS's Module.....on both sides. I'm going to order another 460 relay tomorrow.

Here is a full vag-com scan.


VCDS Version: Beta 812.4
Data version: 20090214

Thursday,19,February,2009,18:58:38:26365

Chassis Type: 1K0
Scan: 01 03 08 09 15 16 17 19 25 42 44 46 47 52 56 7D

VIN: WAUZZZ8P64A039000 Mileage: 165450km/102805miles

00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
03-ABS Brakes -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: Malfunction 0010
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: Malfunction 0010
56-Radio -- Status: Malfunction 0010
7D-Aux. Heat -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine Labels: 03G-906-016-BKD.lbl
Part No SW: 03G 906 016 G HW: 028 101 136 4
Component: R4 2,0L EDC 0000SG 5334
Revision: 12345678 Serial number: AUX7Z0C6FN301U
Coding: 0000072
Shop #: WSC 06435 000 00000

2 Faults Found
18354 - Control Module 1 for Coolant Fan: Defective
P1946 - 000 - -
Freeze Frame:
RPM: 840 /min
Torque: 28.0 Nm
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 14.14 V
Bin. Bits: 00000000
Temperature: 35.1°C
Duty Cycle: 9.6 %

16502 - Engine Coolant Temp. Sensor (G62): Signal too High
P0118 - 000 - -
Freeze Frame:
RPM: 840 /min
Torque: 26.0 Nm
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 14.14 V
Bin. Bits: 00000000
Temperature: 39.6°C
Temperature: 32.4°C

Readiness: 0 0 0 0 0

-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl
Part No: 1K0 907 379 D
Component: ESP FRONT MK60 0102
Coding: 0055942
Shop #: WSC 00012 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 8P0-820-043.lbl
Part No SW: 8P0 820 043 HW: 8P0 820 043
Component: KlimavollautomatH11 0130
Shop #: WSC 06435 000 00000

2 Faults Found
01177 - Engine Control Unit
013 - Check DTC Memory
Freeze Frame:
Fault Status: 01101101
Fault Priority: 3
Fault Frequency: 1
Reset counter: 249
Mileage: 165459 km
Time Indication: 0
Date: 2011.05.19
Time: 18:55:30

Freeze Frame:
ON

01317 - Control Module in Instrument Cluster (J285)
013 - Check DTC Memory
Freeze Frame:
Fault Status: 01101101
Fault Priority: 3
Fault Frequency: 1
Reset counter: 235
Mileage: 165202 km
Time Indication: 0
Date: 2011.04.19
Time: 00:40:16

Freeze Frame:
ON


-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 8P0-907-279-30-H.lbl
Part No SW: 8P0 907 279 K HW: 8P0 907 279 K
Component: Bordnetz-SG H54 2501
Revision: 00H54000 Serial number: 00000008302459
Coding: B78C5F060014100000000000000000000010FF075C060200000000000000
Shop #: WSC 00000 000 00000

Part No: 8P2 955 119
Component: Wischer WWS Audi350 0130
Coding: 16711696
Shop #: WSC 00000

4 Faults Found
00061 - Footwell Lights
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01101100
Fault Priority: 5
Fault Frequency: 1
Reset counter: 249
Mileage: 165429 km
Time Indication: 0
Date: 2011.05.19
Time: 11:49:00

Freeze Frame:
OFF
Voltage: 11.50 V
OFF
ON
OFF
OFF
OFF

01502 - Bulb for Rear Fog; Left (L46)
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01101100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 249
Mileage: 165429 km
Time Indication: 0
Date: 2011.05.19
Time: 11:49:00

Freeze Frame:
ON
Voltage: 10.95 V
ON
ON
OFF
OFF
OFF

01519 - Bulb for Back-Up Lights; Right (M17)
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01101100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 249
Mileage: 165429 km
Time Indication: 0
Date: 2011.05.19
Time: 11:49:00

Freeze Frame:
ON
Voltage: 10.85 V
ON
ON
OFF
OFF
OFF

01259 - Fuel Pump Relay (J17)
009 - Open or Short to Ground
Freeze Frame:
Fault Status: 01101001
Fault Priority: 5
Fault Frequency: 1
Reset counter: 249
Mileage: 165429 km
Time Indication: 0
Date: 2011.05.19
Time: 11:49:00

Freeze Frame:
ON
Voltage: 10.95 V
ON
ON
OFF
OFF
OFF


-------------------------------------------------------------------------------
Address 15: Airbags Labels: 8P0-959-655-84.lbl
Part No SW: 8P0 959 655 F HW: 8P0 959 655 F
Component: Airbag 8.4ED H01 0130
Coding: 0011602
Shop #: WSC 06435 000 00000

1 Fault Found
00588 - Airbag Igniter; Driver Side (N95)
001 - Upper Limit Exceeded - Intermittent - MIL ON

-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 1K0-953-549-MY8.lbl
Part No SW: 1K0 953 549 A HW: 1K0 953 549 A
Component: Lenksäulenmodul 008 0030
Coding: 0000012
Shop #: WSC 06435 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments Labels: 8P0-920-xxx-17-MY7.lbl
Part No SW: 8P0 920 980 HX HW: 8P0 920 980 HX
Component: KOMBIINSTR. VDO H25 0180
Revision: D15 Serial number: 2246ID15100011
Coding: 0004403
Shop #: WSC 00654 210 91808

1 Fault Found
00779 - Outside Air Temp Sensor (G17)
010 - Open or Short to Plus
Freeze Frame:
Fault Status: 00000011
Fault Priority: 7
Fault Frequency: 2
Reset counter: 249
Mileage: 165429 km
Time Indication: 0
Date: 2011.05.18
Time: 20:51:10


-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 1K0-907-530.lbl
Part No SW: 1K0 907 530 B HW: 1K0 907 951
Component: Gateway H08 0070
Revision: 08 Serial number: 170010351735E7
Coding: 3D0F0B42070101
Shop #: WSC 06435 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 25: Immobilizer Labels: 1K0-920-xxx-25.lbl
Part No SW: 8P0 920 980 HX HW: 8P0 920 980 HX
Component: KOMBIINSTR. VDO H25 0180
Revision: D15 Serial number: AUX7Z0C6FN301U
Shop #: WSC 00654 210 91808

No fault code found.

-------------------------------------------------------------------------------
Address 42: Door Elect, Driver Labels: 8P0-959-801-MIN.lbl
Part No: 8P0 959 801 A
Component: Tuersteuerger. H09 0010
Coding: 0000120
Shop #: WSC 06435 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1Kx-909-14x.lbl
Part No: 1K1 909 143 L
Component: EPS_ZFLS Kl.7 0402
Shop #: WSC 00000 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 8P0-959-433.lbl
Part No: 8P0 959 433
Component: KSG H02 0030
Coding: 008800186D288505485AC63000
Shop #: WSC 06435 000 00000

Part No: 1K0 951 605 A
Component: LIN BACKUP HORN H01 1201

Part No: 1K0 907 719
Component: Neigungssensor 002 0002

Component: IRUE No Answer

1 Fault Found
01135 - Interior Monitoring Sensors
004 - No Signal/Communication

-------------------------------------------------------------------------------
Address 47: Sound System Labels: 8Px-035-382.lbl
Part No SW: 8P3 035 382 HW: 8P3 035 382
Component: AB2 SUBWOOFERBOXH23 0100
Revision: 00001 Serial number: 10000001032935
Shop #: WSC 00000 000 00000

No fault code found.

-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. Labels: 8P0-959-802-MIN.lbl
Part No: 8P0 959 802 A
Component: Tuersteuerger. H09 0010
Coding: 0000120
Shop #: WSC 06435 000 00000

1 Fault Found
00933 - Electric Window Motor; Passenger Side (V148)
005 - No or Incorrect Basic Setting / Adaptation - Intermittent

-------------------------------------------------------------------------------
Address 56: Radio Labels: 8P0-035-1xx-56.lbl
Part No SW: 8P0 035 186 HW: 8P0 035 186
Component: concert II EU H52 0060
Revision: 05S Serial number: AUZ2Z3C1257618
Coding: 0001001
Shop #: WSC 06435 000 00000

1 Fault Found
00858 - Connection; Radio ZF Output to Antenna Amplifier
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 249
Mileage: 165442 km
Time Indication: 0
Date: 2011.05.19
Time: 17:03:24


-------------------------------------------------------------------------------
Address 7D: Aux. Heat Labels: 1K0-963-235.lbl
Part No SW: 1K0 963 235 A HW: 1K0 963 235 A
Component: PTC-Element 0303
Revision: 00400000 Serial number:
Shop #: WSC 00000 000 00000

No fault code found.

End ---------------------------------------------------------------------

The strange thing now is the reverse light works when I put it into reverse....since we moved that 449 relay. But errors are still coming up on the DIS. Also rear Fog don't work when switched on with light switch.

I'll try the coding for both rear fogs or select the BACK TO STANDARD BUTTON in long coding and see what happens......

 

[a8 tech back]

relay 460 missing seems to be the simple solution

you could bridge across the contacts for the primary to secondary side as if there was a relay fitted to test the fog or just get the relay lol

 

[J.R.]

relay 460 missing seems to be the simple solution

you could bridge across the contacts for the primary to secondary side as if there was a relay fitted to test the fog or just get the relay lol

I'll get the relay ...on Tuesday..And I'll keep you informed ....

Thanks for your help....

 

[~RS~]

The joys of amateur retrofits ay digzz, lol

 

[J.R.]

Ok Sorted out a couple of things ...bit still having some small issues.

I installed the relay 460 yesterday....and the Reverse Light bulb fault hasn't come up since...

I'm still getting issues with this Left Fog light thing coming up in Vag-com and the DIS. But now it acts very different then before.

When I pull the switch out to turn on the rear fogs on...it comes up with the same error and the fog light do not work. Then the error keeps on coming up on the DIS & Vag-com , It's not until I clear the error.... it don't come up when I turn the ignition any more or Vag-com. But soon as I turn the Rear fog light switch on again ....it starts all over with the error.

Auto-Lights & Mirror Dimmer - Don't work at all.

I'm also trying to get this to work but I'm having a few issues. Comes up with the Below Error:

02071 - Local Databus
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 4
Mileage: 165594 km
Time Indication: 0
Date: 2011.05.24
Time: 18:43:00

Freeze Frame
ON
Voltage: 12.30 V
ON
ON
OFF
OFF
OFF

01520 - Rain and Light Recognition Sensor (G397)
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 4
Mileage: 165594 km
Time Indication: 0
Date: 2011.05.24
Time: 18:43:00

Freeze Frame
ON
Voltage: 12.30 V
ON
ON
OFF
OFF
OFF

This is the Menu I tick in Vag-COM .....even thou I don't have the rain sensors do you still think I should still tick this box ?

 

[Khufu]

what headlight switch you using? I take it you have a later version that supports DRLs? If I try my switch with DRL onto my older non rev CE module my fog lights dont work.

 

[J.R.]

what headlight switch you using? I take it you have a later version that supports DRLs? If I try my switch with DRL onto my older non rev CE module my fog lights dont work.

8J2941531E comes up for the TT but can use in are cars ...as NHN Stated in a Thread. Also same as RS.

 

[a8 tech back]

Do you mean anti dazzle interior mirror, and have you retro fitted this mirror, check the fuse
Check the fogs work with out put test and are the rear lights the correct lights or retro fits
Your lin bus fault is because you do not have rain and light sensor so have you retro fitted auto lights and modified the wiring

 

[a8 tech back]

found the log from my xenon retro fit

Address 09: Cent. Elect. Labels: 8P0-907-279-30-H.lbl
Part No SW: 8P0 907 279 K HW: 8P0 907 279 K
Component: Bordnetz-SG H54 2501
Revision: 00H54000 Serial number: 00000007500978
Coding: 87880F27A01410004D0000000000000000185E175C030000000000000000

 

[a8 tech back]

This is the switch turned on with rear fog....as you can see the switch works...

I don't understand what you mean by doing a dump on byte 4

also I've done a screen shot of the bytes it's currently on at the moment.

Me and RS also found out what was wrong with the interior light......as it was due to a relay in the wrong position. So one solved and 2 more to go....:thumbsup:

ok now I have my log for 2007 3 door a3 retro xenon change byte 3 to 00100111

so


bit 0 tick
bit 1 tick
bit 2 tick
bit 5 tick

try that

 

[J.R.]

Do you mean anti dazzle interior mirror, and have you retro fitted this mirror, check the fuse
Check the fogs work with out put test and are the rear lights the correct lights or retro fits
Your lin bus fault is because you do not have rain and light sensor so have you retro fitted auto lights and modified the wiring

Yes...I'm talking about the dazzle interior mirror not working. no this is not a retro fit...as this was already installed when I bought the car. Yes the rear lights are correct ...Just upgraded to the new rear lights on the 3 door ....and I know they don't need coding...as everybody on here ain't had a problem.. The 1 fog rear does work as I've done a out put test before.

 

[J.R.]

found the log from my xenon retro fit

Address 09: Cent. Elect. Labels: 8P0-907-279-30-H.lbl
Part No SW: 8P0 907 279 K HW: 8P0 907 279 K
Component: Bordnetz-SG H54 2501
Revision: 00H54000 Serial number: 00000007500978
Coding: 87880F27A01410004D0000000000000000185E175C030000000000000000

I've Just used the above code and the problems have been solved...

Thank you very much "a8 tech"

Now I just need to sort out the Auto Lights and the dazzle interior mirror.

 

[Khufu]

wooo, at last

so ultimately was it swapping over a relay & a coding issue?

 

[J.R.]

wooo, at last

so ultimately was it swapping over a relay & a coding issue?

It was Mainly a coding issue.

 

[a8 tech back]

I've Just used the above code and the problems have been solved...

Thank you very much "a8 tech"

Now I just need to sort out the Auto Lights and the dazzle interior mirror.

auto lights and dazzle mirror are on the same circuit so

auto light switch can be checked in measured value block 17 in address 09

2004 wiring auto light sensor anti dazzle mirror

j519 t16a/11 to pin 3 of the light sensor

j519 t12/c3 to light sensor pin 1 (this also picks up the light switch)

light sensor pin 2 to earth

pins 4 and 5 of the light sensor go to the door control units for anti dazzle wing mirrors

2007

pin1 of the light sensor goes to fuse sc4 ignition 15 supply
pin 2 of the sensor goes to earth
pin 3 goes to j519 t12c/1
pins 4&5 goes to the doors again

so pin 1 needs a 15 supply

and pin 3 needs picking up at t16a/11 (i suspect this is a signal)

so in theory just give pin 1 a live to test it works

if it does then find a 15 supply and tap into it via a 5amp in line fuse as you are using 2004 wiring and fuse allocations with the newer central electrics so sc4 fuse will not be valid for your wiring

or tap into the original headlight switch t6/4 for pin 1 of the interior mirror/light sensor

 

[J.R.]

So is the wiring different because of my module ?

 

[a8 tech back]

yes and because of the vehicle build date

I'm basing the wiring from a 2004 and 2007 as K is around 2007 ish

the mirror and sensor really only need 3 things to work.Earth live (ignition live) and signal input

2004 interior mirror was powered from the light switch and 2007 powered via a fused 15 supply

as its a retro fit with added parts then you have to mess around a bit to get things to work as they should, this makes it hard to refer to vehicle specific wiring

you could re wire to the mirror pins at j519 for correct designation if you wish

now all the main stuff is working this should be easy lol

 

[Khufu]

Finally upgraded my A rev to a K rev CE module today having fitted bi-xenons a while back. Having never had xenons originally and K not being a direct replacement for A, I wasnt sure what else apart from coding would need to be done. Turns out on an A, the main beam wires go to where the DRLs and vice versa to that of the K. A bit of rewiring & coding and one more part of the upgrade done. Weekend will see the DRLs wired too

This will leave the job of getting the chrome facelift light with DRL switch working too.

just leave 2 questions:

byte 8, bit 2 - interlock display via CAN-instrments active

and

byte 23, bit 2 - internal turn light control algorithm active

anybody know what they are for?