Wing Mirror Tilt, Auto Fold Mirrors and Parking Sensors Volume

[vinesh]

Hi,

I have recently changed my car to a Audi A4 2.5tdi Quattro.

1)

The car has factory fitted electric memory seats, auto dimming mirrors and electric folding.

I changed the soft code on Saturday to enable alarm beep when locking the car. But since changing the soft code the mirrors don't tilt down when reverse is selected.

Original soft code for conv unit - 07115
Changed to - 08139

2)

I can fold the mirrors via the switch on the drivers door, is there any way of automating this when locking the car?

3)

Final question - Can I change the volume for the front and rear parking sensors?

I have the full version of VAGCOM.


Many thanks

[bearthebruce]

Post a full autoscan of the car so that others can see what is installed and what the part numbers of the modules are.

[vinesh]

Will post the full scan this afternoon.

[NHN]

Hi,

I have recently changed my car to a Audi A4 2.5tdi Quattro.

1)The car has factory fitted electric memory seats, auto dimming mirrors and electric folding.
I changed the soft code on Saturday to enable alarm beep when locking the car. But since changing the soft code the mirrors don't tilt down when reverse is selected.
Original soft code for conv unit - 07115
Changed to - 08139

2)I can fold the mirrors via the switch on the drivers door, is there any way of automating this when locking the car?

3)Final question - Can I change the volume for the front and rear parking sensors?
I have the full version of VAGCOM

No you cant code auto folding with locking, I designed a circuit that does that, its not cheap, but works.

Go into your pdc controller module 76 & check your adaptations channels as there are rear buzzer volume & frequency options that can be changed

Did you have tilt before as I dont recall this in coding on the B6/7 & all you've done is add 1024 to original coding so shouldnt have affected anything else, what other modules have you accessed

http://wiki.ross-tech.com/wiki/index..._System#Coding

[vinesh]

Thanks NHN - I have changed the volume and tone for the rear and fronts.

Here is my autoscan -

VAG-COM Version: Release 311.2-N


Chassis Type: 8E - Audi A4 B6
Scan: 01,02,03,08,09,15,16,17,26,36,37,45,46,55,56,63,76

Address 01 -------------------------------------------------------
Controller: 8E0 907 401 J
Component: 2.5l V6 TDI G000AG 0006
Coding: 02006
Shop #: WSC 63251
00006059 130 106LC150_1.V79142946482
No fault code found.

Address 02 -------------------------------------------------------
Controller: 8E0 927 156 R
Component: AG5 01V 2.5lTDI RdW 2222
Coding: 00001
Shop #: WSC 00000
No fault code found.

Address 03 -------------------------------------------------------
Controller: 8E0 614 517 A
Component: ABS/ESP allrad 3429
Coding: 04457
Shop #: WSC 06435
No fault code found.

Address 08 -------------------------------------------------------
Controller: 8E0 820 043 AB
Component: A4 Klimaautomat 1323
Coding: 00000
Shop #: WSC 63251
No fault code found.

Address 09 -------------------------------------------------------
Controller: 8E0 907 279 F
Component: int. Lastmodul RDW 0517
Coding: 01011
Shop #: WSC 63251
No fault code found.

Skipping Address 15-Airbags

Address 16 -------------------------------------------------------
Controller: 8E0 953 549 N
Component: Lenksáulenmodul 0611
Coding: 01042
Shop #: WSC 63251
No fault code found.

Address 17 -------------------------------------------------------
Controller: 8E0 920 950 M
Component: KOMBI+WEGFAHRS. RB4 D42
Coding: 01401
Shop #: WSC 00262
WAUZZZ8E54A237923 AUZ6Z0D0043239
1 Fault Found:
00668 - Supply Voltage Terminal 30
53-10 - Supply Voltage Too Low - Intermittent

Address 36 -------------------------------------------------------
Controller: 8E0 959 760
Component: Sitzmemory R2 F 0305
Coding: 00002
Shop #: WSC 63251
No fault code found.

Address 45 -------------------------------------------------------
Controller: 8E0 951 177
Component: Innenraumueberw. 0704
Coding: 00001
Shop #: WSC 00000
No fault code found.

Address 46 -------------------------------------------------------
Controller: 8E0 959 433 BC
Component: Komfortgerát T3B 1412
Coding: 08139
Shop #: WSC 63251
No fault code found.

Address 55 -------------------------------------------------------
Controller: 4Z7 907 357
Component: dynamische LWR D09
Coding: 00060
Shop #: WSC 63251
No fault code found.

Address 56 -------------------------------------------------------
Controller: 8E0 035 186 L
Component: concert II GRO 0001
Coding: 01203
Shop #: WSC 63251
No fault code found.

Address 76 -------------------------------------------------------
Controller: 8E0 919 283 A
Component: Parkingsyst. A4 RDW D08
Coding: 01114
Shop #: WSC 63251
No fault code found.

End -------------------------------------------------------

[vinesh]

I have cleared the following fault -

Address 17 -------------------------------------------------------
Controller: 8E0 920 950 M
Component: KOMBI+WEGFAHRS. RB4 D42
Coding: 01401
Shop #: WSC 00262
WAUZZZ8E54A237923 AUZ6Z0D0043239
1 Fault Found:
00668 - Supply Voltage Terminal 30
53-10 - Supply Voltage Too Low - Intermittent

[NHN]

I have the full version of VAGCOM.

VAG-COM Version: Release 311.2-N

It would appear you havnt.

[vinesh]

It would appear you havnt.

Sorry I thought it was the full version.

Lappy belongs to my neighbour, will see him later on

[NHN]

The latest full version is 908.1 using a genuine interface, the shareware older versions are 409 & 311 is a very old version indeed which use a dumb interface as in non genuine.

Why not upgrade to a genuine with latest software with a new release due imminently, PM if interested.

[vinesh]

I will see what the neighbour says and go halves on the cost. Will PM you.

From the sounds of it the mirrors cannot be tilted?
I always thought this is possible with electric and memory seats.

I must be seeing things when I brought the car.

[vinesh]

Read the manual today -

You can only tilt the passenger side wing mirror.

To do this turn the mirror adjusting knob to left (Passenger side) and engage reverse gear. This will tilt the mirror down.

When you put it back into drive or turn the knob to the centre, the mirror will return to the normal set position.

[NHN]

Mirror will return to normal position, urrmm I suggest you test this before commenting that it will do mate, as not always correct.

[vinesh]

Defo returns in the correct setting.

I have my seat set to memory 1 and my brother has it on memory 2. When reverse is selected it fully tilts down then when driving off it returns to the saved position.

I will try it for a couple of days and let you know if it returns to its position.