Hi all.
I just gotten my VCDS cable today and went along to play with it.
Car is MY2010 Audi A3 8P.
Upon first Auto scan 1 error appeared :
So this is my first question, anybody knows how to go about it ?
So later, i kept on playing with the different modules (not changing anything, just seeing the reported values/options and getting to know the software basically.
Then i decided to auto scan again.
Guess what, a second error pops up :
After googling about, i figured that one out with the help of the awesome Ross-Tech WIKI page
(just to document the solution is :
that got rid of that error).
So i kept on fiddling with the program, mainly trying to figure out how to turn the damn DRL Leds on (will open a thread about it, since i can't figure it out yet).
Then i scan for the third time, and a new error appears (WTH??)
Tried resetting the errors but that one keeps coming back.
So my question (2) is, why is this happening and how can i reset it since i am fairly sure that had it been a real problem it would have appeared on my first scan. I highly doubt that something physically broke during my 30 minutes of fiddling with VCDS.
Thanks in advance guys!
P.S Here's the full scan (the one without the last error, i forgot to save it as a log) just to show all the modules.
Wednesday,16,January,2013,17:22:05:32264 VCDS Version: Release 11.11.3 Data ve - Pastebin.com
I just gotten my VCDS cable today and went along to play with it.
Car is MY2010 Audi A3 8P.
Upon first Auto scan 1 error appeared :
Code:
Address 01: Engine (CCZ) Labels: 06J-907-115-CCZ.clb
Part No SW: 8P0 907 115 AE HW: 8P0 907 115 Q
Component: 2.0l R4/4V TFSI 0020
Revision: AAH07--- Serial number: AUX7Z0I7FNR00R
Coding: 0103100C1C070160
Shop #: WSC 06314 000 00000
VCID: 75EBFF0D1CDA171
1 Fault Found:
001089 - EVAP Emission Control Sys
P0441 - 000 - Incorrect Flow - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 0
Fault Frequency: 3
Mileage: 40857 km
Time Indication: 0
Date: 2013.01.09
Time: 18:11:11
Freeze Frame:
RPM: 840 /min
Load: 25.1 %
Speed: 0.0 km/h
Temperature: 99.0°C
Temperature: 43.0°C
Absolute Pres.: 930.0 mbar
Voltage: 13.208 V
So this is my first question, anybody knows how to go about it ?
So later, i kept on playing with the different modules (not changing anything, just seeing the reported values/options and getting to know the software basically.
Then i decided to auto scan again.
Guess what, a second error pops up :
Code:
1 Fault Found:
01539 - Headlights Not Adjusted
005 - No or Incorrect Basic Setting / Adaptation - MIL ON
Freeze Frame:
Fault Status: 11100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 252
Mileage: 41720 km
Time Indication: 0
Date: 2013.01.16
Time: 17:16:47
After googling about, i figured that one out with the help of the awesome Ross-Tech WIKI page
(just to document the solution is :
Code:
[B]Headlight Adjustment[/B]
[COLOR=#000000][FONT=Arial][B][Select][/B]
[B][55 - Xenon Range][/B]
[B][Basic Settings - 04][/B]
Group 001
[B][Go!][/B]
Activate the Basic Setting.
[B][ON/OFF/Next][/B]
[/FONT][/COLOR]
[LIST]
[*]The meas. block field now shows "Wait" and should switch to "Adjust Headlights" then (this may take up to 10 seconds).
[*]Adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target.
[/LIST][COLOR=#000000][FONT=Arial][B][ON/OFF/Next][/B]
The adjustment should now be learned.
[B][Done, Go Back][/B]
Don't forget to check/clear fault codes afterwards.
[/FONT][/COLOR][B][Close Controller, Go Back - 06][/B]
that got rid of that error).
So i kept on fiddling with the program, mainly trying to figure out how to turn the damn DRL Leds on (will open a thread about it, since i can't figure it out yet).
Then i scan for the third time, and a new error appears (WTH??)
Code:
Address 03: ABS Brakes (-----) Labels: 1K0-907-379-60EC1F.clb
Part No SW: 1K0 907 379 AP HW: 1K0 907 379 AP
Component: ESP MK60EC1 H45 0107
Revision: 00H45001
Coding: 144260120A2700FC281206E9501A00413900
Shop #: WSC 06314 000 00000
VCID: 80051ED91318A29
1 Fault Found:
01309 - Power Steering Control Module (J500)
008 - Implausible Signal
Freeze Frame:
Fault Status: 01101000
Fault Priority: 3
Fault Frequency: 1
Reset counter: 252
Mileage: 41715 km
Time Indication: 0
Date: 2013.01.16
Time: 18:52:10
Freeze Frame:
Count: 0
Count: 12
Count: 12800
Count: 8212
Count: 48640
Count: 0
Count: 0
Count: 0
Tried resetting the errors but that one keeps coming back.
So my question (2) is, why is this happening and how can i reset it since i am fairly sure that had it been a real problem it would have appeared on my first scan. I highly doubt that something physically broke during my 30 minutes of fiddling with VCDS.
Thanks in advance guys!
P.S Here's the full scan (the one without the last error, i forgot to save it as a log) just to show all the modules.
Wednesday,16,January,2013,17:22:05:32264 VCDS Version: Release 11.11.3 Data ve - Pastebin.com
Last edited: