Is there any guide (with pics) that show how to do the above?
Is there any guide (with pics) that show how to do the above?
Found a few threads on other forums with alright pics but not 100%.
I was thinking of buying the Darkside kit, £50, anyone got one?
Also, is the inlet manifold straight forward to remove?
What's the dark side kit mate?
Darkside 1.9 8v TDI VE 90 / 110 and PD100 / PD115 EGR Delete / Race Pipe (51mm) - Darkside Developments
I know you can achieve, essentially, the same result with 2 manufactured metal plates that cover the orifices when the EGR is out, but I fancy something a little more aesthetically pleasing, however, it might not necessarily be better than the £7-10 eBay ones.
Nice, might have to invest in that
Thats^^ a nice site for VAG TDis, gonna have a mooch :)
^They do a kit for the AFN engine too, I think its called the VE one IIRC, its 51mm instead of the 57mm PD one, but as you say you can change the manifolds apparently, I might have read it wrong though ??
If your still skeptical I'd just phone them and get a straight answer over the phone and agree with them that if by some unforeseen circumstance the kit doesn't bolt straight on no hassle then you can return.
Fair enough, might do that when the missus gives me back the card
tried with a set of the bolt grips for rounded nuts on the outside of said nuts but there's always one that refuses to budge.
i needed airbox out and pipework removed...
in the Spring might try with a blowtorch
you might be lucky though - spray on some plusgas and give it a try?
You checked the manifold has the bolted flange for that kit?
AFN's i've seen i'm pretty sure dont have it.
This is what they say on the website Darkside 1.9 8v TDI VE 90 / 110 and PD100 / PD115 EGR Delete / Race Pipe (51mm) - Darkside Developments
I queried the fitment of the above kit on the AFN engine as it did not specify on their website, I was assured it would be compatible the website just needs amending, I would of thought they know what there talking about?
Looks nice and shiney,
I cannot see how that kit would fit the AFN without a different or even custom inlet mainfold -
mind you, as the kit is for PD100/115 perhaps one of those inlets could be used?
I went with the cheapo 4mm steel plates off ebay and saved the change for a remap...
Can you point me in the direction of the cheap kits on ebay, ie a linky :)
Iam still waiting to have a go at my inlet decoke and EGR deletion, BTW if anyone is finding undoing the hex bolts hard, a little tip (which works on most bolts including wheel studs) if you can get at it tap it quite firm with a hammer or put a bit in with an extension and hit that hard inwards, nearly ALWAYS works, as for the wheel nuts, place an impact socket over the nut and belt it fookin ard, a few times you will be amazed :) I scrap cars for a living and often come accross stubborn wheel nuts, honestly even some that wont budge with a 4 ft breaker can often be easily undone with a standard brace after a good WHACK! lol :)
Vw golf mk4 1.9 TDI Inlet Manifold ARL 150bhp 038129713AF | eBay
Thats a golf manifold, and as you can see has a flange with a massive EGR assembly, which the darkside kit replaces with a nice plain fitting.
Compare that to the photo of the A4 manifold i posted above, and you'll see that theres nowhere for that flange to go. Instead the A4 has it cast in, and has a seperate external valve.
All you need for an AFN is two steel plates and two gaskets which should cost less than a tenner.
I have ping'd an email off to Darkside and once again challenged there compatibility of this kit on the AFN engine. Being a new Audi owner and with little engine knowledge on this particular car, I suppose I took confidence in what Darkside told me the 1st time, if this ends up being the wrong kit, which, is looking increasingly likely, having seen the 2 different manifolds and flange in the kit, I guess lesson learned.
I shall feedback the response from Darkside when I get it.
Interestingly enough, VAG themselves make an EGR delete plate:
Part number 038131925
The plate is £2.80 and you probably want a new gasket too.
Aragorn, you were spot on with your observation, the kit Darkside said would be compatible, dispite me asking for confirmation it was the correct kit, was in fact for a different set up all together. As far as I'm lead to believe the only way you can delete the EGR is to use, quite simply, 2 blankings plates. The kit I purchased feature 1 blanking plate and having justified that this particular kit wasn't correct they said send it back minus the blanking plate, we'll send you another one free of charge and refund you the £50 plus postage expense for returning the kit, so although it was been a little bit of a ball ache to sort it out, I've walked away with 2 genuine blanking plates for cock all, winner!
My next question, what do people recommend to plug the flexible pipe the comes of the EGR valve itself?
this pic kindly posted by aragorn shows where to put the plates - one of each of the sets of bolts are visible
remove this flexi-pipe and keep the bolts
Most of the blanking plates available simply locate onto each manifold at the point where the flexi-pipe currently sits.
That's how I did mine anyway, hope it helps
I'd remove the EGR valve and the flexi pipe entirely.
Fit one blank to the exhaust manifold inplace of the flexi, and fit the other blank to the inlet manifold in place of the EGR Valve. Remove the lines to the EGR solenoid and blank them off. You'll need to leave the solenoid connected electrically or you'll get a fault code.
So to clarify;
The 2 areas I have circled yellow is where you blank off?
My next question is what do you do with flexi pipe coming off the valve itself? Where does the solenoid electrically connect to, location that is?
The AFN engine is fitted to many different VAG cars, they say it will fit but they might have only used it on a VW AFN engine.
The A4 AFN engine is different and this kit will not fit.
For the price of that kit you could buy every AFN owner on this forum a set of blanking plates.
The AFN Blanking plates that Aragorn posts up are for the AFN generator engines, they don't need EGR vavles so they just blank them off.
BE warned that most EGR blanking kits will offer you the same size blank for the inlet and exhaust side.
The Exhaust blank is easy fine, no issues but the the 2nd blank for the EGR side, goes between the EGR and the exhaust side, not between the EGR and inlet.
The inlet side of the EGR is smaller.
So you keep the EGR valve and the flexi pipe.
If you want to go one step further and remove the EGR, you will need a smaller blank, I've not seen theses on Ebay so I made my own.
The flexi pipe was closed via a bolt and cable tied and hidden in the bay.
It now looks like this.
What ever blanks you go for, make sure you get a new gasket for both the exhaust and inlet size.
The ebay and my own made blank for the inlet side will seep oil out. I got no idea why and I've been unable to stop it.
I've gone through multiple blanks and gaskets and it still leaks.
I would recommend trying the VAG blanks in the hope this stops the oil leak.
I will at some point by the VAG blanks once I got my finger out.
I'll look into gaskets for blanking plates, can't be more that a couple of quid each from TPS?
On a different note, super clean bay! Is your car PFL or FL, there's a lot of plastic trim in your bay that I don't have i.e. around the washer bottle, over the airbox, scuttle panel and battery cover. Did PFL cars have these fitted? Defo getting some FL headlights, look so much better than PFL!
Thanks for your reply.
Here my engine bay at present;
and as you can see, it's missing almost everything!?
Is the Passat stuff bolt on? Also, I see in the engine bay thread you mentioned 2 bits, PAS cover and airbox cover that you can source from VAG themselves? As you said in that thread they match in design so would be a better choice for continuity but does the airbox cover fit properly?
All genuine VAG parts.
The washer bottle cover needs little trimming for the pipes then it's easy enough.
The air box cover is ok. It's a little wobble when touching but that's cause our box has not got any clamps.
I'll get some better pics on wednesday.
Might source the original air box cover, although it doesn't match the Passat PAS and washer bottle cover, it still looks very clean and tidy, like yours.
More pics would be ace, thanks.
Now trying to source the scuttle cover and air box cover, should be fun!? Know anyone selling?
I'm after the following engine bay trim for a B5 1.9 TDi;
Air box cover
Scuttle cover inc. battery cover and additional bit of plastic that lives in the top right hand corner as you look at the engine.
If anyone can point me in the direction of the above that's for sale or know someone who's breaking that would be brill!
I've contacted several breakers on eBay, some don't have what I'm after and some I'm waiting to hear back...
Dimple ABS, screen wash cover from Passats. 3B0 119 487 C £37.09
I think most facelift B5s will have the scuttle cover, so any breaker breaking a B5 should have one. Unless he sold it.
If you want the facelift battery cover, you also need the two plastic trims that run along the bottom of the windscreen, as they're different to the PFL ones.
Thanks for the replies guys.
Will the Passat air box cover, pictured above, securely fit?
Also regarding the scuttle cover, I understand that I need one from a FL car but how many separate pieces does it have? I can see this being a right pain in the arse to source unless 1 car has everything in need?
Do I need FL wipers?
It's not going to fall off and fall down between the engine. There is a clip on the cover and on the car that matches up and secures it. so no need to worry about it.
The scuttle cover is 5 parts.
the 2 plastic bits under the windscreen held in by the wipers, the main long cover, the battery cover and the rubber strip.
You don't need FL wipers but they look better.
I've just placed an order with TPS for the air box and ABS/screen wash cover. £19.51 for air box cover and £33.29 for ABS cover.
I think it's going to be very difficult to source the scuttle unless I physically go to a scrappy that has everything still in tact, I can see it being complicated to explain the various components via eBay for example.
I would personally get the parts your self.
It will give you a better idea of how they come off, you make sure you got everything, no missing clips and less chance of it breaking in the post.
So just to clarify about EGR blanking on an AFN lump, after blanking the 2 holes, I need to leave the rubber hose just blanked off with say a bolt or similar and all will be ok?