AH FabricationsVolks Autos
Results 1 to 6 of 6
  1. #1
    Neutral

    Status
    Offline
    Join Date
    Oct 2007
    Location
    cork ,ireland
    Posts
    73

    on board computer

    hello all

    i bought a cruise control and new wiper lever with on board computer controls

    coded it all with vag com cruise works perfect but when i press mode button display in cluster just goes blank

    i was just wonder in this is a coding issue or maybe it just not available on my car

    all suggestions accepted

    ciaran
    a4 v6 2.5tdi b6 18"rs rns-e genuine bt quattro chipped to 210hp mfsw,cruise control, ashtray ipod connector,

  2. # ADS
    ADS
    Join Date
    Always
    Location
    Global
    Posts
    Many
     
  3. #2
    5th Gear

    Status
    Offline
    Join Date
    Jan 2007
    Location
    Hampshire
    Posts
    1,155
    Hmmm sounds like it 'could' be a coding issue, what VAG-COM coding did you do to enable the trip computer?
    A6 3.0 TDI.

  4. #3
    Neutral

    Status
    Offline
    Join Date
    Oct 2007
    Location
    cork ,ireland
    Posts
    73

    on board

    thank isaac

    i did not enable wtih vagcom yet because i didnt no how to do it and i cant find n threads on it


    if u have codes i would be grateful

    thanks

    a4 v6 2.5tdi b6 18"rs rns-e genuine bt quattro chipped to 210hp mfsw,cruise control, ashtray ipod connector,

  5. #4
    5th Gear

    Status
    Offline
    Join Date
    Jan 2007
    Location
    Hampshire
    Posts
    1,155
    Control Module Adaptation
    Select 17 (Instrument Cluster)Adaptation -> Function 10
    -> Channel 19 (Misc)
    xxxx?: Remote Clock
    0 - Remote Clock not active
    1 - Remote Clock active
    xxx?x: Ambient Temperature
    0 - no Display, Illumination inactive
    1 - Display and Illumination active
    xx?xx: Driver Information System (DIS)
    0 - DIS 1
    1 - Highline without DIS
    2 - DIS 2
    x?xxx: Board Computer
    0 - only Level 2 (long time memory)
    1 - Level 1 and 2
    ?xxxx: Illumination Option
    0 - Needle and Scala only active at 'Light on"
    1 - Needle already active at 'Ignition on'
    2 - Scale already active at 'Ignition on'
    3 - Scala (2. Map) and Needle at "ignition on" active

    Taken from http://http://en.openobd.org/audi/a4_8e.htm#17

    These are what I used to code in my B7. You may have a slight issue with the low washer fluid warning staying on permanently, Depends wether you already have the low level sensor in your washer bottle?

    Check out the following thread from TSN DIS retrofit
    Last edited by Issac Hunt; 10th November 2007 at 22:37.
    A6 3.0 TDI.

  6. #5
    Neutral

    Status
    Offline
    Join Date
    Oct 2007
    Location
    cork ,ireland
    Posts
    73

    as above

    thank issac

    coding worked a treat
    1010 or 1110

    do u know how to solve the washer bottle problem,

    regards

    ciaran
    a4 v6 2.5tdi b6 18"rs rns-e genuine bt quattro chipped to 210hp mfsw,cruise control, ashtray ipod connector,

  7. #6
    5th Gear

    Status
    Offline
    Join Date
    Jan 2007
    Location
    Hampshire
    Posts
    1,155
    try this link instead, dunno what was wrong with the last one. I'll try to edit it.

    Basically you can fix the washer by either fitting and wiring up the sensor in the washer bottle or grounding the wire for it to earth to turn it off.
    I think from memory its the blue connector on the rear of the speedo housing, pin 1 I think but have a good read of that thread to make sure!
    A6 3.0 TDI.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Single Sign On provided by vBSSO

Garage Plus, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

Content Relevant URLs by vBSEO