Fault codes

[nickaudi41]

Hi everyone,

I ran VAGcom and got the following:

Address 01: Engine
Controller: 8D0 907 551 K
Component: 2.7l V6/5VT G 0001
Coding: 10711
Shop #: WSC 06435
WUAZZZ8DZ1N901949 AUZ7Z0Y1578245
1 Fault Found:
16825 - EVAP Emission Control Sys: Incorrect Flow
P0441 - 35-10 - - - Intermittent
Readiness: 0000 0000

-------------------------------------------------------------------------------
Address 03: ABS Brakes
Controller: 8D0 907 389 E
Component: ABS/ESP allrad D56
Coding: 04395
Shop #: WSC 00899
1 Fault Found:
01435 - Brake Pressure Sensor 1 (G201)
35-10 - - - Intermittent

Thanks in advance

Kind Regards

Nick

 

[jesters3]

16825/P0441/001089 - EVAP Emission Control Sys: Incorrect Flow

Possible Symptoms

• Malfunction Indicator Light (MIL) active

Possible Causes

• Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80) faulty/jammed
• Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115) faulty/jammed
• Evaporative Emission (EVAP) Canister Sealing faulty
• Pipes between Tank Breathing and Throttle Body leaky/blocked

Possible Solutions

• Check Evaporative Emission (EVAP) Canister Purge Regulator Valve (N80)
  • Perform Output Test
• Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve (N115)
• Check Evaporative Emission (EVAP) Canister
  • Perform Basic Setting
• Check Pipes between Tank Breathing and Throttle Body #

01435 - Brake Pressure Sensor 1 (G201): No or Incorrect Basic Setting / Adaptation

Possible Symptoms

• Malfunction Indicator Light (MIL) active

Possible Causes

• Basic Setting not performed

Possible Solutions

• Perform Basic Setting

01435 - Brake Pressure Sensor 1 (G201): Electrical Fault in Circuit

Possible Causes

• Brake Pedal Switch (F) faulty/jammed
• Brake Pressure Sensor 1 (G201) faulty

Possible Solutions

• Check/Replace Brake Pedal Switch (F)
  • See Measuring Blocks
• Check/Replace Brake Pressure Sensor 1 (G201)
  • ABS Hydraulic Unit (N55) may need to replaced
  • Perform Brake Pump Bleeding
  • Perform Brake Pressure Sensor 1 (G201) Basic Setting
  • Replace Brake Electronics Control Module (J104)

Retrieved from "http://wiki.ross-tech.com/index.php/01435"

 

[nickaudi41]

Thanks Jesters3, I will check and report back.

 

[S3 Chris]

Hi Nickelvery - did you come to a solution for the EVAP code?
the same one has cropped up on my S3 this week.

Cheers

 

[jesters3]

Do you have any issues with your fuel flap? i.e you get a hissing sound of the pressure being released when undoing the the fuel cap?

 

[S3 Chris]

nope i dont get any noise when opening the fuel flap.
what would that indicate out of interest?

 

[jesters3]

It would indicate a ******** gravity valve in the fuel tank, meaning a fuel tank off job to get to it.

But you haven't got that so all is good!!

On the EVAP issue, have a look around the canister to see if any leakages are there.

 

[S3 Chris]

certainly will do.
..... erm wheres it located?!

you needing an RS3 badge by the way - just noticed your sig and I've got one kicking around the garage thats still in the packet

 

[jesters3]

Next to the Power Steering Fluid container it has the hoses coming out of it.

Unforunately not as I haven't got an RS3 yet and I doubt I ever will, then again you never know!